For those who have already done this, what kit did you use,
ie has anyone used the ESM kit was it OK?
I believe frontline has a 6 month lead time.
Any other suggestions I already have a gearbox but not the short tail one.
Search found 34 matches
- Wed Aug 16, 2023 8:11 am
- Forum: Mechanical
- Topic: Type 9 conversion
- Replies: 2
- Views: 989
- Fri Apr 21, 2023 2:19 pm
- Forum: Mechanical
- Topic: 1275 Marina engine runs better with air filter sealed?
- Replies: 12
- Views: 1142
Re: 1275 Marina engine runs better with air filter sealed?
Try change the needle in carb to AAA
- Sun Feb 19, 2023 8:19 am
- Forum: Mechanical
- Topic: Pull starter
- Replies: 4
- Views: 485
Re: Pull starter
Perfect thank you
- Sat Feb 18, 2023 8:23 pm
- Forum: Mechanical
- Topic: Pull starter
- Replies: 4
- Views: 485
Pull starter
My pull starter has stopped working so I guess it's the solenoid as the pin still works. What's the best way to change it
- Fri Dec 30, 2022 5:51 pm
- Forum: General Discussion
- Topic: 1275 identification
- Replies: 5
- Views: 509
Re: 1275 identification
Top man Phil really appreciate it I will keep you informed
- Fri Dec 30, 2022 12:46 pm
- Forum: General Discussion
- Topic: 1275 identification
- Replies: 5
- Views: 509
Re: 1275 identification
So here is the block also took pics of flywheel as I was told it was in a minor before,
- Wed Dec 28, 2022 8:41 pm
- Forum: General Discussion
- Topic: 1275 identification
- Replies: 5
- Views: 509
Re: 1275 identification
I'll get them Phil
- Wed Dec 28, 2022 7:14 pm
- Forum: General Discussion
- Topic: 1275 identification
- Replies: 5
- Views: 509
1275 identification
Just a double check I've bought a 1275 and the oil filter is beside dizzy by back of block so from what I've read that's a marina. However when I looked up the block number it says mg? 12G, any ideas I'm told it was in a minor before so hoping the front and back plates are correct.
- Thu Dec 22, 2022 4:45 pm
- Forum: Mechanical
- Topic: 940 head
- Replies: 7
- Views: 404
Re: 940 head
Single groove valves 29 & 33 maybe its a mix and match Thanks Phil have a good Xmas mate
- Thu Dec 22, 2022 3:24 pm
- Forum: Mechanical
- Topic: 940 head
- Replies: 7
- Views: 404
Re: 940 head
Here is the head also made a mistake with compression calcs lol works out 8.91
- Wed Dec 21, 2022 10:44 pm
- Forum: Mechanical
- Topic: 940 head
- Replies: 7
- Views: 404
Re: 940 head
I will take some pics tomorrow
- Wed Dec 21, 2022 9:21 pm
- Forum: Mechanical
- Topic: 940 head
- Replies: 7
- Views: 404
940 head
I've bought a 1275 engine it's been built before, When i looked up heads there are 2x 940 heads 1 with 33mm valve 1 with 35 mine is the 33. So I've measured the head and seems it's had 20thou off already I've cc the combustion chamber it's 23cc but when I've read normally it's 21cc does anyone have ...
- Sat Jul 23, 2022 10:50 am
- Forum: General Discussion
- Topic: Doors
- Replies: 3
- Views: 293
Re: Doors
Ah makes sense thanks everyone
- Sat Jul 23, 2022 8:26 am
- Forum: General Discussion
- Topic: Doors
- Replies: 3
- Views: 293
Doors
Hi can anyone tell me if the drivers door is the same on a 2 door and 4 door
Thanks
Thanks