Search found 10724 matches
- Thu Apr 18, 2024 7:44 pm
- Forum: Mechanical
- Topic: Stronger Halfshafts
- Replies: 11
- Views: 189
Re: Stronger Halfshafts
The anti-tramp bars fitted to my Minor and made by myself have been on there for many years and are very similar to the ESM kit but predates the ESM kit by many years. The bars are of a similar length to the ESM bars and do not need to be longer. They are attached under the spring at the rear and be...
- Thu Apr 18, 2024 6:18 pm
- Forum: Mechanical
- Topic: Stronger Halfshafts
- Replies: 11
- Views: 189
Re: Stronger Halfshafts
The problem with fitting stronger half-shafts is - you move the failure point somewhere else. Unless you are in absolute need of stronger half-shafts the standard half-shafts are more than adequate. Having stronger half-shafts on the shelf will not solve the problem of possible half-shaft failure - ...
- Thu Apr 18, 2024 3:46 pm
- Forum: Mechanical
- Topic: Spark plugs
- Replies: 13
- Views: 274
Re: Spark plugs
If fitted correctly the cork gasket is just as good as the silicon rubber gasket.
The silicon rubber gasket is overkill IMHO.
The silicon rubber gasket is overkill IMHO.
- Thu Apr 18, 2024 8:32 am
- Forum: Bodywork
- Topic: Poly bushes
- Replies: 16
- Views: 189
Re: Poly bushes
The thickness of the flange on a poly bush is not dependent upon the colour or supplier. I have several poly bushes of different colours and from different branded suppliers and the thickness of the flanges varies. There is no dedicated poly bush for the chassis and no dedicated poly bush for the sp...
- Wed Apr 17, 2024 5:06 pm
- Forum: Parts for sale
- Topic: Starter dog/crankshaft bolt spanner
- Replies: 0
- Views: 61
- Tue Apr 16, 2024 4:43 pm
- Forum: Do you know....?
- Topic: Engine, best guess
- Replies: 3
- Views: 101
Re: Engine, best guess
Not a early 'A' Series but a BMC 'B' Series. Possibly a 1.8 unit from a commercial vehicle..
- Tue Apr 16, 2024 10:20 am
- Forum: Mechanical
- Topic: What tappet chest gasket do I need?
- Replies: 8
- Views: 178
Re: What tappet chest gasket do I need?
There are specialists and specialists!!
- Mon Apr 15, 2024 6:20 pm
- Forum: Mechanical
- Topic: Hub identification disc brakes
- Replies: 10
- Views: 297
Re: Hub identification disc brakes
When fitting the taper bearings to the Minor stub it can requires a spacer washer (or even two spacer washers) between the bearing and nut. The Marina hub nut does not have any castellation's, it is a plain nut and is secured by the castellated locking ring. I suspect that the hub nut used and shown...
- Mon Apr 15, 2024 4:26 pm
- Forum: Mechanical
- Topic: Ford gearbox
- Replies: 3
- Views: 123
Re: Ford gearbox
No circlips. the UJ and output shaft just pulls out of the rear of the gearbox.
- Mon Apr 15, 2024 8:37 am
- Forum: Mechanical
- Topic: What tappet chest gasket do I need?
- Replies: 8
- Views: 178
Re: What tappet chest gasket do I need?
The fibre washer is not a direct replacement for the neoprene seal no matter what the MOSS site indicates. The bolts are a different length dependent upon the washer/seal used. The bolt can bottom out before clamping the seal if the wrong washer/seal is used. The parts have to be replaced as a set. ...
- Sun Apr 14, 2024 8:48 pm
- Forum: Mechanical
- Topic: What tappet chest gasket do I need?
- Replies: 8
- Views: 178
Re: What tappet chest gasket do I need?
The 1098cc engine has neoprene gaskets and the steel covers have a raised outer edge. The bolts also have rubber seals and cup washers fitted over the seal. The front cover is Pt No: 12A1212 The rear cover is Pt No: 12H941. The gasket for both covers is Pt No: GUG5505 GM The rubber bolt seal is Pt N...
- Sun Apr 14, 2024 6:48 pm
- Forum: Mechanical
- Topic: Spark plugs
- Replies: 13
- Views: 274
Re: Spark plugs
In many cases the gasket moves out of position when the rocker cover is fitted. Gluing the gasket to the rocker cover helps reduce that happening. Greasing the face of the gasket against the head also helps keep the gasket supple and stops the gasket sticking to the head when the rocker cover is rem...
Re: Hoses
The I.D. of the heater hose that goes through the bulkhead is 1/2".
- Sun Apr 14, 2024 4:57 pm
- Forum: Mechanical
- Topic: Spark plugs
- Replies: 13
- Views: 274
Re: Spark plugs
Make sure that the sealing ring seat in the head is clean and free of crud. Scrape around the seat and then turn the engine over to blow away any crud. As regards the rocker cover gasket - clean the rocker cover gasket seat apply general purpose glue to the rocker cover gasket seat and fit the gaske...
- Sun Apr 14, 2024 9:07 am
- Forum: Mechanical
- Topic: Clutch problem, Borg & Beck pressure plate
- Replies: 6
- Views: 155
Re: Clutch problem, Borg & Beck pressure plate
The fingers that fit under the pressure pad have to be set up correctly - that is the height of each finger. There may be an underlying problem with the fingers but which is not insurmountable. Removing the pressure pad should quickly show up what is wrong.
- Sat Apr 13, 2024 5:35 pm
- Forum: Free!
- Topic: qty 2 948cc block/crank/pistons assys
- Replies: 3
- Views: 147
Re: qty 2 948cc block/crank/pistons assys
I would not go so far as to say no work is required but they are in too good a condition to just throw away.
Just north of Romsey in the Test Valley.
Just north of Romsey in the Test Valley.
- Sat Apr 13, 2024 3:20 pm
- Forum: Free!
- Topic: qty 2 948cc block/crank/pistons assys
- Replies: 3
- Views: 147
qty 2 948cc block/crank/pistons assys
Free to a good home I have made an executive decision :wink: and will not be progressing any further on building a uprated 998cc in line 'A' Series engine. The block assys are in good condition, the coolant galleries have been soaked in citric acid and are clean. The better of the two blocks I belie...
- Sat Apr 13, 2024 2:55 pm
- Forum: Mechanical
- Topic: A-series 1098 rebuild video (also blocked breather)
- Replies: 10
- Views: 282
Re: A-series 1098 rebuild video (also blocked breather)
If you look down onto the top of the pedestals in the photo immediately above - the impression is of looking down at a bulls head. They were produced in both alloy and forged steel - not sintered. They have scalloped sides which allows for some metal to be removed for rocker alignment. The sintered ...
- Sat Apr 13, 2024 2:50 pm
- Forum: General Discussion
- Topic: Grease
- Replies: 2
- Views: 155
Re: Grease
Les
The grease shown above is suitable as is ordinary Castrol LM grease or similar.
Poly bushes will work with just about any grease.
The grease shown above is suitable as is ordinary Castrol LM grease or similar.
Poly bushes will work with just about any grease.
- Sat Apr 13, 2024 10:59 am
- Forum: Mechanical
- Topic: A-series 1098 rebuild video (also blocked breather)
- Replies: 10
- Views: 282
Re: A-series 1098 rebuild video (also blocked breather)
Because it is easier to have a pedestal with oil transfer hole under one part number than have several variations of pedestals with different part numbers. The extra hole is not expensive to produce. The 'bull head' pedestals in the photo above were made in alloy (chuck them in the scrap bin even th...