Search found 816 matches

by gtt1951
Fri Jun 21, 2019 11:43 pm
Forum: Electrical
Topic: UFN 456 Electrics
Replies: 2
Views: 315

Re: UFN 456 Electrics

Bought a voltage/current regulator from Bryan (private purchase, not from club spares). Finally put it into circuit and the power wires now have just over 12V - the original fitted one was cooking one of the coils, as it turns out. The indicators now work and I'll be able to refit the wiper motor. T...
by gtt1951
Fri Jun 21, 2019 2:47 pm
Forum: Series MM Register
Topic: Clutch Pedal Return Spring
Replies: 1
Views: 236

Re: Clutch Pedal Return Spring

Drove the car up and down the cul-de-sac I live in, for a short road test and the return spring definitely needed to be connected.
Found the hole it goes into at the side of the R/H chassis leg.
by gtt1951
Fri Jun 21, 2019 10:30 am
Forum: Series MM Register
Topic: Oil leak from Side-valve oil filter mounting
Replies: 47
Views: 1615

Re: Oil leak from Side-valve oil filter mounting

Thicker paper gasket hasn't stopped the dribble leak - I even used a scraper on the mounting point surface to make sure that there were no leftover bits of previous gaskets. Interestingly, there is a small hole in the mounting surface, that doesn't have a corresponding hole in the Purolator head fit...
by gtt1951
Thu Jun 20, 2019 8:49 am
Forum: Series MM Register
Topic: Oil leak from Side-valve oil filter mounting
Replies: 47
Views: 1615

Re: Oil leak from Side-valve oil filter mounting

Got the engine fired up again, but the thin paper oil gasket is leaking. I will try the next thickness up.
I still haven't had a chance to look at the HOF250 filters.
G.
by gtt1951
Thu Jun 06, 2019 12:17 am
Forum: Series MM Register
Topic: Clutch Pedal Return Spring
Replies: 1
Views: 236

Clutch Pedal Return Spring

How is this connected and which anchorage points should it be using?
This is a Side-Valve engine and Gearbox, converted from LHD to RHD.
by gtt1951
Wed Jun 05, 2019 5:54 pm
Forum: Series MM Register
Topic: Oil leak from Side-valve oil filter mounting
Replies: 47
Views: 1615

Re: Oil leak from Side-valve oil filter mounting

Hello Rob, I still haven't found a suitable sized spin-on filter (length), but will go look at the HOF250 one that you mention.
At the moment, I'm using the original Purulator unit. George.
by gtt1951
Wed Jun 05, 2019 5:50 pm
Forum: Series MM Register
Topic: Sloppy brake & clutch pedal shaft
Replies: 21
Views: 909

Re: Sloppy brake & clutch pedal shaft

Thanks Phil. I ended up doing the sequence I had written about as a possibility. Had to get the M/C loose again, but first undid the banjo bolt. Screwed the banjo through bolt onto the brake pipe union and it went in nicely, so not belled. Left it done up only a few turns so the pair could rotate ar...
by gtt1951
Sun Jun 02, 2019 7:30 pm
Forum: Series MM Register
Topic: Sloppy brake & clutch pedal shaft
Replies: 21
Views: 909

Re: Sloppy brake & clutch pedal shaft

I've now got another problem - I can't refit the brake pipe union into the Banjo Bolt retaining bolt IMG_20190602_155221.jpg I've even tried with holding the pipe up with a pair of wire cutters (cross-jaw type to hold up the pipe). I just cannot get the correct angle to screw the union nut back in :...
by gtt1951
Sun Jun 02, 2019 7:20 pm
Forum: Series MM Register
Topic: Sloppy brake & clutch pedal shaft
Replies: 21
Views: 909

Re: Sloppy brake & clutch pedal shaft

Phil, I used a bolt, large washers and a nut to pull the bronze bush it (then tried with the new Clutch pedal and it goes in, but a little "tight". I have got the Master Cylinder out, having got info via another thread. I used the suggestion of having a stout piece of wood resting on an axle stand a...
by gtt1951
Sun Jun 02, 2019 7:08 pm
Forum: Series MM Register
Topic: Oil leak from Side-valve oil filter mounting
Replies: 47
Views: 1615

Re: Oil leak from Side-valve oil filter mounting

Phil,
I have now replaced the cork gasket with the thin paper one.
Won't know if this will seal better until I fire up the engine, but the car is on axle stands and engine is in gear whilst I work on the pedals and master cylinder (another thread).
by gtt1951
Tue May 28, 2019 7:31 pm
Forum: Mechanical
Topic: What has happened to all the old website technical instructions?
Replies: 4
Views: 279

Re: What has happened to all the old website technical instructions?

The photo of the method of prising the torsion bar downwards is very helpful - I did not find this in all the posts that came up with my original search query. Many thanks, has given me some ideas but, as you say, what happened to the original store of Technical Tips we used to have, like polarizing...
by gtt1951
Tue May 28, 2019 6:33 pm
Forum: Mechanical
Topic: What has happened to all the old website technical instructions?
Replies: 4
Views: 279

What has happened to all the old website technical instructions?

I've been try to get hold of MMOC instructions on how to do things the "easy way", but it looks like these were never migrated (just like the photos in the old posts) to the new website. What I want was originally referenced by this article, which now throws up an error. http://www.mmoc.org.uk/index...
by gtt1951
Mon May 27, 2019 9:04 pm
Forum: Series MM Register
Topic: Sloppy brake & clutch pedal shaft
Replies: 21
Views: 909

Re: Sloppy brake & clutch pedal shaft

I'm back! I ordered the bits I needed, which arrived on Saturday. Today I resumed work on the car. Decided to do a test of the Master Brake Cylinder - topped it up, placed the original push-rod with yoke into it, did a bit of pumping, producing a few air bubbles and what looked like a wisp of smoke!...
by gtt1951
Sun May 19, 2019 6:06 pm
Forum: Series MM Register
Topic: Sloppy brake & clutch pedal shaft
Replies: 21
Views: 909

Re: Sloppy brake & clutch pedal shaft

I've got a "parts required" spreadsheet and the bushes, new pedal, yoke and brake pedal cylinder actuating rod are in the list, from ESM, together with a few other items totalling in excess of the min (pre vat) price for free delivery. Will be placing the order when I get home on Thursday. Moss, unf...
by gtt1951
Fri May 17, 2019 12:05 pm
Forum: Series MM Register
Topic: Sloppy brake & clutch pedal shaft
Replies: 21
Views: 909

Re: Sloppy brake & clutch pedal shaft

Phil, Its interesting that Moss Europe use the BMC part numbers in their catalogue. My chassis rail, unfortunately, does not have a bush in the outer wall and that is why the shaft was sloppy. I'll be buying a replacement "new" clutch pedal from ESM when I get back next week. Many thanks for your he...
by gtt1951
Thu May 16, 2019 11:37 pm
Forum: Series MM Register
Topic: Sloppy brake & clutch pedal shaft
Replies: 21
Views: 909

Re: Sloppy brake & clutch pedal shaft

All four (two in the chassis leg and two in the brake pedal) bushes are the same Pt No: AAA1423. Ah, that is the Moss Europe part number, ESM and Bull Motif part number is COM104, Charles Ware is CBS131, GS Jones CBS148 (pair). Thank you Phil for confirming that these are all the same bushes. The 2...
by gtt1951
Thu May 16, 2019 8:23 pm
Forum: Series MM Register
Topic: Sloppy brake & clutch pedal shaft
Replies: 21
Views: 909

Re: Sloppy brake & clutch pedal shaft

I wonder if the old bushes are still in the other chassis leg? :D I'll have a look after I get back from a short break away. [got a picture from when I first took off the tunnel cover - don't know how the clutch pedal would have come through the floor, unless another bit of metal has now been added...
by gtt1951
Thu May 16, 2019 8:16 pm
Forum: Series MM Register
Topic: Oil leak from Side-valve oil filter mounting
Replies: 47
Views: 1615

Re: Oil leak from Side-valve oil filter mounting

Phil, the tractor gasket is a different shape and size and I was going to use that when I got the 90mm M10 bolts (which arrived today, but I had to move the car yesterday).
by gtt1951
Thu May 16, 2019 3:39 pm
Forum: Series MM Register
Topic: Oil leak from Side-valve oil filter mounting
Replies: 47
Views: 1615

Re: Oil leak from Side-valve oil filter mounting

Hello Phil,
I have gasket paper in the gasket sheet pack that I got the cork one out of - I've got 2 thicknesses 0.35mm and 1.2mm.
The gasket that came in the "tractor" screw-in filter adapter is 0.8mm. Guess I should use the thicker paper.

George.
by gtt1951
Thu May 16, 2019 3:24 pm
Forum: Series MM Register
Topic: Sloppy brake & clutch pedal shaft
Replies: 21
Views: 909

Re: Sloppy brake & clutch pedal shaft

In the struggle to get the split-pin out, the whole pedal and push-rod came out! IMG_20190516_124600.jpg The clevis pin wouldn't come out so, after using my trusty butane blow-lamp, it did come out IMG_20190516_131436.jpg IMG_20190516_131736.jpg The chassis leg does have a bush on the inside wall (n...