Search found 565 matches

by Murrayminor
Fri Jul 31, 2020 11:34 am
Forum: Problems with the Messageboard
Topic: Ignoring a thread
Replies: 1
Views: 515

Re: Ignoring a thread

I just click on the "New posts" tab at the top of the page and scroll through.
If I want to see who has replied to a post I click on the "Your Posts" tab that way I can just ignore the posts I don't feel relevant
by Murrayminor
Thu Jul 30, 2020 8:58 am
Forum: General Discussion
Topic: Wheeler dealers
Replies: 3
Views: 337

Re: Wheeler dealers

Whilst the idea of the Wheeler Dealer show is good, it all just seems too stage managed and false. They need a down to earth presenter to really get under the skin of the cars and maybe cover the renovation of one vehicle over a few episodes. Checking classifieds , buying a car, renovating it and se...
by Murrayminor
Thu Jul 30, 2020 7:18 am
Forum: Mechanical
Topic: Mg Midget 1275 gearbox rebuild
Replies: 39
Views: 1370

Re: Mg Midget 1275 gearbox rebuild

Hi Dermot I have just re-assembled my 3rd motion shaft this evening, before I did I spent a bit of time working out just what the purpose of the little rounded end pin is. I concluded that it is there to prevent the inner hub moving back towards 2nd gear whilst 1st gear is engaged , the only reason...
by Murrayminor
Wed Jul 29, 2020 4:56 pm
Forum: Mechanical
Topic: Mg Midget 1275 gearbox rebuild
Replies: 39
Views: 1370

Re: Mg Midget 1275 gearbox rebuild

I have discovered wear in both the pin and the gear.
Maybe that was the issue all along.
Enquiries have been made to source a new gear and pin.
I'm concerned about the quality of new gears,but it cannot be any worse than a worn old gear.
by Murrayminor
Wed Jul 29, 2020 10:54 am
Forum: Bodywork
Topic: Andrew Eggleton vs ESM
Replies: 26
Views: 2358

Re: Andrew Eggleton vs ESM

I suppose its similar to your favourite beer, we each have our preferences.

Just be thankful we have competition within the Morris Minor panel industry, a friend of mine was given a MK1 Cortina recently and the cost to replace the front wings was £750...each!!
by Murrayminor
Wed Jul 29, 2020 10:32 am
Forum: Mechanical
Topic: Mg Midget 1275 gearbox rebuild
Replies: 39
Views: 1370

Re: Mg Midget 1275 gearbox rebuild

Having thought about it overnight I think the pin in the gear set would be hardened therefore unlikely to be worn, but I wonder if the gear is actually worn beyond tolerances.
by Murrayminor
Tue Jul 28, 2020 6:52 pm
Forum: Mechanical
Topic: Using Marina torsion bar adjusters
Replies: 18
Views: 824

Re: Using Marina torsion bar adjusters

Absolutely excellent engineering there Phil.
Wonderful to see an expert at work, well done.
by Murrayminor
Tue Jul 28, 2020 6:43 pm
Forum: Mechanical
Topic: Mg Midget 1275 gearbox rebuild
Replies: 39
Views: 1370

Re: Mg Midget 1275 gearbox rebuild

The first picture shows the mainshaft.

The second image shows how far the first gear has moved, leading me to suspect the locking pin.

The steel plate in the last picture is a mount I made up so I can hold the gearbox casing in the vice while working on it.
by Murrayminor
Tue Jul 28, 2020 6:42 pm
Forum: Mechanical
Topic: Mg Midget 1275 gearbox rebuild
Replies: 39
Views: 1370

Re: Mg Midget 1275 gearbox rebuild

Another couple of hours misery with this gearbox. It was all ready, the main shaft was going in but the reverse gear was fouling it's progress, I lifted out the main shaft again and snap went the gear, it didn't go all the way so the balls popped out but far enough for one to pop out when I examined...
by Murrayminor
Tue Jul 28, 2020 1:56 pm
Forum: Mechanical
Topic: Gearbox input shaft Oil seal.
Replies: 19
Views: 525

Re: Gearbox input shaft Oil seal.

Phil

I read that the 2A3087 cover may require further machining to allow movement of the shift rod as the recess on the cover is too shallow, is that not the case?

Regards

Dermot.
by Murrayminor
Tue Jul 28, 2020 9:45 am
Forum: Off-Topic
Topic: E scooters
Replies: 44
Views: 1846

Re: E scooters

One of my pet hates is drivers throwing litter and I used to regularly stop vehicles and request the occupant to pick up their litter even if it meant stopping the traffic. It showed the public we were out there watching and secondly showed them something was being done to uphold standards. Sadly no...
by Murrayminor
Tue Jul 28, 2020 8:35 am
Forum: Mechanical
Topic: Gearbox input shaft Oil seal.
Replies: 19
Views: 525

Re: Gearbox input shaft Oil seal.

I have a 22g118 front cover made by BIRMAL and there is hardly sufficient metal in the area of the boss to allow a seal to be fitted. I also have three 2A3087 front covers made by C & A. and BIRMAL. The internal and external shapes/forms are slightly different in all cases. I also have three differ...
by Murrayminor
Tue Jul 28, 2020 7:56 am
Forum: Mechanical
Topic: Gearbox input shaft Oil seal.
Replies: 19
Views: 525

Re: Gearbox input shaft Oil seal.

pgp001 wrote:
Tue Jul 28, 2020 7:00 am
Dermot

Can you see a part number on your casting ?

Phil
Yes its 22G118
by Murrayminor
Tue Jul 28, 2020 6:16 am
Forum: Mechanical
Topic: Stuttering at 50+
Replies: 10
Views: 471

Re: Stuttering at 50+

To properly clean the tank and to ensure any loose flakes of rust are removed it will have to come out. The tank on my minor was in a horrendous state, the car was running but occasionally it stuttered, on removal of the tank the amount of rust that came out had to be seen to be believed. I then cle...
by Murrayminor
Tue Jul 28, 2020 6:08 am
Forum: Mechanical
Topic: Gearbox input shaft Oil seal.
Replies: 19
Views: 525

Re: Gearbox input shaft Oil seal.

If you read my post in the link above you will see that I made the comment that not all the scroll boss's are the same and shape/thickness is dependent upon the manufacturer - so one seal does not fill the one size criteria. Phil I did indeed read your post and very informative it was, my cover app...
by Murrayminor
Mon Jul 27, 2020 5:05 pm
Forum: Mechanical
Topic: Gearbox input shaft Oil seal.
Replies: 19
Views: 525

Re: Gearbox input shaft Oil seal.

I have been to my local machine shop but they think there is not enough meat in the cover to accept the seal I have. They were going to weld around the hole, then machine it flat to accept the seal. At £100 I declined their offer. Reading the other excellent post makes me think is it worth the hassl...
by Murrayminor
Mon Jul 27, 2020 4:11 pm
Forum: Mechanical
Topic: Gearbox input shaft Oil seal.
Replies: 19
Views: 525

Gearbox input shaft Oil seal.

I have seen the modified input shaft oil seal cover advertised for sale. As I have the original scroll seal, is the newer seal worth the expense? Would I be able to ream my existing cover out to take the new oil seal? Does anyone know if there is enough "meat" on the cover to simply ream the area ou...
by Murrayminor
Mon Jul 27, 2020 3:13 pm
Forum: Off-Topic
Topic: E scooters
Replies: 44
Views: 1846

Re: E scooters

Thanks for explaining that Murrayminor. Very interesting. Surely we can't go on like this; something needs to change! Unfortunately UK Governments, whichever flavour you prefer,seem to think by throwing a few extra bobbies at the problem its solved. The stark truth is the 20,000 officers promised w...
by Murrayminor
Mon Jul 27, 2020 11:30 am
Forum: Off-Topic
Topic: E scooters
Replies: 44
Views: 1846

Re: E scooters

My sympathy is also with the police Murrayminor. However, a few years ago I did a Freedom of Information request and asked how many pavement cyclists had been issued with a fixed penalty notice in the last 12 months in Nottinghamshire. The answer was....none. A couple of years ago I asked the same ...
by Murrayminor
Mon Jul 27, 2020 10:38 am
Forum: Restoration Projects
Topic: "Gracie" Dove grey 1965 2 door saloon.
Replies: 44
Views: 2827

Re: "Gracie" Dove grey 1965 2 door saloon.

A quick update I have now acquired a front disc brake set up from a Morris Marina including swivels etc. They have been put into storage boxes until the body work is complete. I'm still working on the gearbox rebuild and will be dropping the bellhousing cover off for machining to allow fitment of a ...