Search found 197 matches
- Tue Jun 02, 2020 6:20 pm
- Forum: Bodywork
- Topic: advice on polish
- Replies: 15
- Views: 2341
Re: advice on polish
it dosnt look to bad but with a car that age should it be perfect you would be surprised mate the blue vw had been through car washes and the paint was a right mess the Aston took me about 30hrs to do (was a mates so no rush) this was his pervious aston before DSCF1161.JPG DSCF1162.JPG after DSCF13...
- Mon Jun 01, 2020 8:18 pm
- Forum: Bodywork
- Topic: advice on polish
- Replies: 15
- Views: 2341
Re: advice on polish
all depends on budget and personal preference
i have polish/ waxes that cost only a few quid up to nearly £100
here is my morris along with the shelves stocked with too much stuff!! lol and here's a couple of 'old bangers ' i did for mates
i have polish/ waxes that cost only a few quid up to nearly £100
here is my morris along with the shelves stocked with too much stuff!! lol and here's a couple of 'old bangers ' i did for mates
- Mon May 25, 2020 8:57 pm
- Forum: Mechanical
- Topic: mg gearbox
- Replies: 9
- Views: 1364
Re: mg gearbox
yeah hence i thought i would check with someone with more know how than me
many thanks
many thanks
- Mon May 25, 2020 8:48 pm
- Forum: Mechanical
- Topic: mg gearbox
- Replies: 9
- Views: 1364
Re: mg gearbox
ok mate
cheers for the diagram very helpful
the box im looking at doesn't have a rev switch set up
and going by the info on the diagram its a 1098 minor box as the shaft number shows?
it was the hydraulic clutch that threw me
cheers for the diagram very helpful
the box im looking at doesn't have a rev switch set up
and going by the info on the diagram its a 1098 minor box as the shaft number shows?
it was the hydraulic clutch that threw me
- Mon May 25, 2020 8:18 pm
- Forum: Mechanical
- Topic: mg gearbox
- Replies: 9
- Views: 1364
mg gearbox
hi all can anyone give me any info on mg midget gearboxes i have the chance of a mg midget box with an output shaft number 22g171 it has hydraulic clutch which make me believe its defo a midget box unless any knows different am i right in thinking its a 1098 midget box not a 1275(which I'm after) an...
- Tue May 19, 2020 3:54 pm
- Forum: Mechanical
- Topic: servo
- Replies: 14
- Views: 1990
Re: servo
ok mate many thanks for the info
i had a strange feeling that was the case so i have ordered a couple of new brake pipes
so i can rotate the servo
cheers
i had a strange feeling that was the case so i have ordered a couple of new brake pipes
so i can rotate the servo
cheers
- Mon May 18, 2020 9:06 pm
- Forum: Mechanical
- Topic: servo
- Replies: 14
- Views: 1990
Re: servo
hi
i used the bracket supplied with servo which makes the 'nose' slightly higher than the rear ?
Stu
i used the bracket supplied with servo which makes the 'nose' slightly higher than the rear ?
Stu
- Mon May 18, 2020 11:49 am
- Forum: Mechanical
- Topic: servo
- Replies: 14
- Views: 1990
Re: servo
Hi as for the coil it was fitted there before i decide to fit a servo!
i made up the bracket once i changed from dynamo to alternator
i made up the bracket once i changed from dynamo to alternator
- Mon May 18, 2020 11:39 am
- Forum: Mechanical
- Topic: servo
- Replies: 14
- Views: 1990
Re: servo
cheers for that i had heard/seen that the servo should be 'twisted' slightly so the
white vent? is to the side??
white vent? is to the side??
- Mon May 18, 2020 11:25 am
- Forum: Mechanical
- Topic: servo
- Replies: 14
- Views: 1990
servo
hi all
any pictures of the correct orientation of the brakes servo set-up?
just to double check
as i have fitted it the same way i have seen some done but i am sure i have now read
that it should be fitted in a different way??
sorry for dodgy pic
any pictures of the correct orientation of the brakes servo set-up?
just to double check
as i have fitted it the same way i have seen some done but i am sure i have now read
that it should be fitted in a different way??
sorry for dodgy pic
- Sun May 03, 2020 2:51 pm
- Forum: Electrical
- Topic: Rear lighting / fuel sender loom routing
- Replies: 31
- Views: 5458
Re: Rear lighting / fuel sender loom routing
thanks for the pics looking good
stu
stu
- Sat May 02, 2020 4:50 pm
- Forum: Electrical
- Topic: Rear lighting / fuel sender loom routing
- Replies: 31
- Views: 5458
Re: Rear lighting / fuel sender loom routing
thanks mate
i like the idea of running inside as well to save all the grud over the wiring loom
any ore pics of the engine bay wiring?
cheers
Stu
i like the idea of running inside as well to save all the grud over the wiring loom
any ore pics of the engine bay wiring?
cheers
Stu
- Fri May 01, 2020 3:20 pm
- Forum: Electrical
- Topic: Rear lighting / fuel sender loom routing
- Replies: 31
- Views: 5458
Re: Rear lighting / fuel sender loom routing
hi mate
what gauge of wire did you use for the rear loom??
cheers
Stu
what gauge of wire did you use for the rear loom??
cheers
Stu
- Thu Apr 23, 2020 9:59 pm
- Forum: Electrical
- Topic: SPEEDOMETER LED's
- Replies: 6
- Views: 1554
- Thu Apr 09, 2020 6:43 pm
- Forum: Mechanical
- Topic: jacking beam
- Replies: 16
- Views: 1521
Re: jacking beam
being used
- Thu Apr 09, 2020 6:43 pm
- Forum: Mechanical
- Topic: jacking beam
- Replies: 16
- Views: 1521
Re: jacking beam
some more pics
the pin depends on the hole on the jack pad area
the pin depends on the hole on the jack pad area
- Thu Apr 09, 2020 6:28 pm
- Forum: Mechanical
- Topic: jacking beam
- Replies: 16
- Views: 1521
Re: jacking beam
hi sorry its had to be done this way this is the overall length of the beam IMG_20200409_121506711.jpg this is the size of the top plate (i notched the box section to recess the plate you don't have to do that if your jack will allow the beam to fit under the car) i needed no more than 70mm in total...
- Wed Apr 08, 2020 4:56 pm
- Forum: Mechanical
- Topic: jacking beam
- Replies: 16
- Views: 1521
Re: jacking beam
hi
sorry for the delay
trying to upload pics but the site keeps telling me the file is too big to add to message!
i will try another way
sorry for the delay
trying to upload pics but the site keeps telling me the file is too big to add to message!
i will try another way
- Tue Apr 07, 2020 9:56 pm
- Forum: Mechanical
- Topic: Brake master cylinder replacement tool
- Replies: 5
- Views: 754
Re: Brake master cylinder replacement tool
Great mate
cant wait to get to work to fab up one of these
might even make a couple more if the need arises
again cheers for the sizes
cant wait to get to work to fab up one of these
might even make a couple more if the need arises
again cheers for the sizes
- Tue Apr 07, 2020 6:40 pm
- Forum: Mechanical
- Topic: Brake master cylinder replacement tool
- Replies: 5
- Views: 754
Re: Brake master cylinder replacement tool
great idea i might make one up when i get back to work
any sizes of the item available ?? length, height ??
any sizes of the item available ?? length, height ??