Page 2 of 2

Re: My 68 saloon restoration /customization project.

Posted: Sat Jun 09, 2018 9:13 pm
by >Thomas63<
Here's a few of the process
20180531_193748.jpg
20180531_193748.jpg (4.38 MiB) Viewed 837 times
20180514_113318.jpg
20180514_113318.jpg (3.87 MiB) Viewed 837 times
20180514_131500.jpg
20180514_131500.jpg (3.63 MiB) Viewed 837 times
20180602_120705.jpg
20180602_120705.jpg (4.85 MiB) Viewed 837 times
20180602_135801.jpg
20180602_135801.jpg (3.04 MiB) Viewed 837 times
Spec:

Compleatly rebuilt with all new parts.

1275 A+ Ital block. Skimmed, bored out at diamond honed to 1293.
12G940 head, port polish, skimmed, lead free, 3 angle grind, new valves and piper double valve springs.
9.4/1 compression balanced pistons, balanced rods.
Crank ground, polished and balanced.
Piper 270 cam.
Rebuilt HIF44 carb, k&n pancake filter.
Duplex timing kit with a 3degree woodruf key giving me 107 ATDC
Ford type 9 box, lightened and balanced re-faced flywheel with Sierra 7.5 inch clutch and balanced clutch plate. Hydrolic clutch conversion kit with defender master cylinder. Viper point free electronic ignition system, race leads and hotter nkg plugs.

An yea.... I painted it white.... I'll regret that soon enough...

Thomas.

Re: My 68 saloon restoration /customization project.

Posted: Mon Jun 25, 2018 8:54 pm
by >Thomas63<
So I finished up the engine and got it all in, car runs smooth as gravy sandwich.
2018-06-15_16.47.26.jpg
2018-06-15_16.47.26.jpg (4.29 MiB) Viewed 776 times
2018-06-15_16.49.21.jpg
2018-06-15_16.49.21.jpg (3.81 MiB) Viewed 776 times
This is how it looks at the moment.
2018-06-25_18.36.44.jpg
2018-06-25_18.36.44.jpg (2.95 MiB) Viewed 776 times
2018-06-25_18.42.35.jpg
2018-06-25_18.42.35.jpg (3.54 MiB) Viewed 776 times
Balanced 1293 with cam and carb

type 9 box and hydrolic clutch

disk breaks and servo

Lowered 2 clicks and 2.5" rear block.

Fiberglass front clip, doors, rear arches, boot lid and gearbox cover/floor.

All perspex Windows minus windscreen.

Banded moggi wheels 8" Rear (205) 5.5" front (145)

Keyless ignition and push button start

Remote pop doors

Full dyno matted minus the floor.

Next on the list is a dyno tune and then just to drive and enjoy. I'll be finishing up any bits of bodywork on the move and getting the car wrapped before the end of the year.

I'll be fitting a standard moggi interior into it when I can get my hands on some.

At some point I'll also be looking at a front anti roll bar, maybe fit some shocks or look at full modern suspension.

Then the rear end, hardened half shafts and a quaif diff.

No rush though, for now just having it back on the road is good enough for me.

Thanks for the several hundred views and big thanks to the 2 or 3 individuals that dropped a comment.

Thomas.

Re: My 68 saloon restoration /customization project.

Posted: Mon Jun 25, 2018 8:57 pm
by >Thomas63<
20180623_125115.jpg
20180623_125115.jpg (4.31 MiB) Viewed 776 times

Re: My 68 saloon restoration /customization project.

Posted: Wed Jun 27, 2018 9:19 pm
by >Thomas63<
2018-06-27_20.54.23.jpg
2018-06-27_20.54.23.jpg (1.61 MiB) Viewed 737 times

Re: My 68 saloon restoration /customization project.

Posted: Thu Jun 28, 2018 11:40 am
by myoldjalopy
JY = Plymouth registration. My great auntie bought a black, de-luxe, four-door saloon in Plymouth in 1957 - NJY 581, sadly now long gone to the scrappie. Then a trafalgar blue one EJY ****? in the mid-60's. I still remember the plastic seat protectors it had when she bought it. At that point the old, black Morris was sold to my parents......I guess it was that one that started it all for me 8)

Re: My 68 saloon restoration /customization project.

Posted: Thu Jun 28, 2018 10:28 pm
by >Thomas63<
myoldjalopy wrote:
Thu Jun 28, 2018 11:40 am
JY = Plymouth registration. My great auntie bought a black, de-luxe, four-door saloon in Plymouth in 1957 - NJY 581, sadly now long gone to the scrappie. Then a trafalgar blue one EJY ****? in the mid-60's. I still remember the plastic seat protectors it had when she bought it. At that point the old, black Morris was sold to my parents......I guess it was that one that started it all for me 8)
I didn't know that about the registration. Thanks for the info, very cool.

Thomas.

Re: My 68 saloon restoration /customization project.

Posted: Fri Jun 29, 2018 9:57 am
by myoldjalopy
I recall that the 'area code' for vehicle registration numbers (last two letters) used to be listed in the old AA Handbook at one time but, for those that are interested, here is a link to help identify where your car originated from http://nice-reg.co.uk/info/area-of-issu ... lates.html
These did change a bit at various times (e.g. JY for Plymouth later became the code for Exeter in around 1980) but I believe Minor production had stopped before there were many changes. It will be of interest to owners to see if their car has remained 'local' all its life or has travelled!

Re: My 68 saloon restoration /customization project.

Posted: Fri Jun 29, 2018 11:59 am
by palacebear
This site is useful for reg.no. history, up to the time when Local Vehicle Licencing Offices took over vehicle licencing responsibilities from local councils (circa 1974-ish). It gives a year-by-year breakdown of letter combinations issued. Handy for dating original 'dateless' or non-suffix letter plates.

http://www.oldclassiccar.co.uk/registra ... etters.htm