Wiring harness/Loom check

Discuss Electrical problems here.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
Post Reply
Murrayminor
Minor Addict
Posts: 564
Joined: Mon Oct 15, 2018 9:47 am
MMOC Member: Yes

Wiring harness/Loom check

Post by Murrayminor »

Good evening
My 1965 2 door Minor "Gracie" is off the road for some much needed body repair work.
Tonight I decided to remove the wiring harness to evaluate its condition and generally check it was ok prior to beginning any welding.
Well pardon the pun but I was shocked how bad the harness was,it had chafed through to the visible wires in a number of places.
The harness running across the front cross member had all but cut through to the visible inner wire.
I thank the stars I looked at it and more importantly It didn't catch fire.
So not to sound too alarmist but take the time to have a root round and check the state of your wiring harness.

Dermot.
Proud owner of my first Morris Minor
JOWETTJAVELIN
Minor Legend
Posts: 2775
Joined: Mon Dec 12, 2011 7:20 pm
Location: LANCASHIRE (paradise)
MMOC Member: Yes

Re: Wiring harness/Loom check

Post by JOWETTJAVELIN »

The outer wrapping, usually fabric, binding the bunch of individual cables together usually wears through in time where it rubs against the body. That can be sorted with pvc insulation tape and moving it away from the rubbing point if possible. But exposed copper conductors through wear or any other fault need urgent rectification.
Murrayminor
Minor Addict
Posts: 564
Joined: Mon Oct 15, 2018 9:47 am
MMOC Member: Yes

Re: Wiring harness/Loom check

Post by Murrayminor »

Indeed, I had to remove the heater hose from the engine bay and noticed where the loom runs behind the bracket on the inner wing had not only rubbed through the outer wrapping but had begun to actually work its way through the wires themselves.
These wires are normally out of sight.
I suppose given my car is over 50 years old it is to be expected, but I was alarmed to see how close it was to causing major issues.
For peace of minds sake I would take a few minutes to thoroughly check your own wiring loom.
Proud owner of my first Morris Minor
ianmack
Minor Addict
Posts: 835
Joined: Sat Jul 05, 2014 7:02 pm
MMOC Member: Yes

Re: Wiring harness/Loom check

Post by ianmack »

The cloth outer covering isn’t very durable and I think it was mostly for holding the wires together for ease of assembly. If it has deteriorated it can be replaced with modern plastic sleeve, either in tubular form if the end is accessible or coiling around if not.
JOWETTJAVELIN
Minor Legend
Posts: 2775
Joined: Mon Dec 12, 2011 7:20 pm
Location: LANCASHIRE (paradise)
MMOC Member: Yes

Re: Wiring harness/Loom check

Post by JOWETTJAVELIN »

Aye, cloth binding was ditched in favour of pvc tape in the late 1950's/early 60's. You can buy new fabric covering if you want to keep it looking right, I think Autosparks sell it.
IslipMinor
Minor Legend
Posts: 2147
Joined: Mon May 10, 2004 9:10 pm
Location: Oxford, UK
MMOC Member: Yes

Re: Wiring harness/Loom check

Post by IslipMinor »

Autosparks will recover/re-braid your harness using exactly the same colours as the original. Not cheap, but not silly either, and they will cover whatever you send them, so any additions, modifications can all be incorporated and look like they were there all along.

Excellent service the 2 times I have used them.
Richard


Murrayminor
Minor Addict
Posts: 564
Joined: Mon Oct 15, 2018 9:47 am
MMOC Member: Yes

Re: Wiring harness/Loom check

Post by Murrayminor »

IslipMinor wrote: Tue Aug 13, 2019 3:57 pm Autosparks will recover/re-braid your harness using exactly the same colours as the original. Not cheap, but not silly either, and they will cover whatever you send them, so any additions, modifications can all be incorporated and look like they were there all along.

Excellent service the 2 times I have used them.
Now then there's a point, would it be better to have my old harness rebraided or buy a new modern harness?
Are the modern harness made of the same material and gauge?
Proud owner of my first Morris Minor
IslipMinor
Minor Legend
Posts: 2147
Joined: Mon May 10, 2004 9:10 pm
Location: Oxford, UK
MMOC Member: Yes

Re: Wiring harness/Loom check

Post by IslipMinor »

Autosparks also provide a new harness to the original specification by chassis number. I believe they will incorporate additional circuits as well.

https://www.autosparks.co.uk/finder

Your 1965 Minor will have PVC covered cables with a coloured braiding. Unless it has suffered physical damage, the basic harness will probably be fine to re-use, but is likely to need some new terminations and bullet connectors (unless you are very lucky!).

Probably worth looking at each option?
Richard


Post Reply