I recently started a thread about fitting a water temp sender gauge, and then another thread about my attempt that ended in failure - I'm now pleased to say this has now been successful fitted!
I 'borrowed' a few drops from a friend's Loctite 2400 threadlock bottle for the job, and decided I will buy some Loctite threadlock for myself - I will lock the thermostat housing nuts and heater tap valve nuts that seem to loosen themselves from time to time - but there a number of different Loctite threadlock products available, many which seem to do the same thing - eg Loctite 242, 243 and 2400. Any a few more. Which should I get?
Which Loctite threadlock numbers do you all use, and for which applications?
Many thanks!
Pete
Which Loctite threadlock to use?
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
Re: Which Loctite threadlock to use?
I don’t know the numbers but there are various strengths, ie medium, high, etc. I wouldn’t use the strong variety in fact I wouldn’t use any on the nuts you mention. In fact I would give the threads a smear of copper grease. It’s unusual for the nuts to come loose.
Last edited by les on Tue Sep 15, 2020 8:25 pm, edited 1 time in total.
-
- Minor Maniac
- Posts: 10775
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Which Loctite threadlock to use?
I use Loctite 243 Lock & Seal. It is a good all-round locking and sealing fluid.
https://www.ebay.co.uk/itm/10-ml-Thread ... Sw6xxe40uq
Loctite has a use by date so I would advise against purchasing large amounts. I always write date of purchase on the packaging.
https://www.ebay.co.uk/itm/10-ml-Thread ... Sw6xxe40uq
Loctite has a use by date so I would advise against purchasing large amounts. I always write date of purchase on the packaging.
- geoberni
- Minor Legend
- Posts: 3578
- Joined: Fri Aug 04, 2017 11:19 am
- Location: North Leicestershire
- MMOC Member: Yes
Re: Which Loctite threadlock to use?
243 is a good medium strength threadlock.
When I was in the RAF we used loads of different numbers on different fixings and pity anyone who got the numbers mixed up. If you got it wrong you could either fail to lock a big bolt, or lock a small one so much you'd wreck it when it came to removal.
This is a good application chart for car use. 270 is for applications like Cylinder Head bolts. But these days the range is far wider, with tread locking pastes amongst other products.
I think you'll find a lot of Loctite products are typically 12 mth life from manufacture, but personally I think there's a fair bit of leeway on that.
For decades, the RAF supply system used to recall oils/lubricants/sealants etc where the manufacturers life had been reached, batch test them and extend the life if they were still fit for purpose.
It was not unusual to see Loctite that had been extended by 6 or 12 months; now if that was good enough for aircraft use....
I would say, if in doubt about a bottle that is over it's date, do your own sample test on a bolt/nut.
When I was in the RAF we used loads of different numbers on different fixings and pity anyone who got the numbers mixed up. If you got it wrong you could either fail to lock a big bolt, or lock a small one so much you'd wreck it when it came to removal.
This is a good application chart for car use. 270 is for applications like Cylinder Head bolts. But these days the range is far wider, with tread locking pastes amongst other products.
I think you'll find a lot of Loctite products are typically 12 mth life from manufacture, but personally I think there's a fair bit of leeway on that.
For decades, the RAF supply system used to recall oils/lubricants/sealants etc where the manufacturers life had been reached, batch test them and extend the life if they were still fit for purpose.
It was not unusual to see Loctite that had been extended by 6 or 12 months; now if that was good enough for aircraft use....
I would say, if in doubt about a bottle that is over it's date, do your own sample test on a bolt/nut.
Basil the 1955 series II
-
- Minor Legend
- Posts: 1657
- Joined: Thu May 12, 2016 6:33 am
- MMOC Member: No
Re: Which Loctite threadlock to use?
As Les, I would use spring washers in those applications. Don’t think I’ve had them come loose on either item - ever.
Re: Which Loctite threadlock to use?
Thanks all for your replies.
A couple of years ago I bought a replacement thermostat housing/cork gasket/bolts/nuts/washers kit from ESM - looking at the kit, it does not come with spring washers, and I wonder if that is why the nuts tended to come loose - combined with a squishy cork gasket.
I replaced my squished cork gasket with a new gasket after keen eyed @philthehill saw the photo of my failed water temp sender fitting (thanks Phill!) and that is why I want to use the Loctite, as I don't want the nuts to loosen again. Or should I replace the flat washers with sprung washers? Likewise on my heater tap valve. It sounds like @Les and @oliver90owner use sprung washers?
Kit from ESM Squished cork gasket New gasket in place
A couple of years ago I bought a replacement thermostat housing/cork gasket/bolts/nuts/washers kit from ESM - looking at the kit, it does not come with spring washers, and I wonder if that is why the nuts tended to come loose - combined with a squishy cork gasket.
I replaced my squished cork gasket with a new gasket after keen eyed @philthehill saw the photo of my failed water temp sender fitting (thanks Phill!) and that is why I want to use the Loctite, as I don't want the nuts to loosen again. Or should I replace the flat washers with sprung washers? Likewise on my heater tap valve. It sounds like @Les and @oliver90owner use sprung washers?
Kit from ESM Squished cork gasket New gasket in place
-
- Minor Maniac
- Posts: 10775
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Which Loctite threadlock to use?
You do not need to use Locktite on the thermostat studs/nuts - use spring washers between the flat washers and the nuts.
If you can find them - wide flat spring washers can be used without the flat washers.
https://www.ebay.co.uk/itm/UNF-IMPERIAL ... SwpLNX~jpw
If you can find them - wide flat spring washers can be used without the flat washers.
https://www.ebay.co.uk/itm/UNF-IMPERIAL ... SwpLNX~jpw
Re: Which Loctite threadlock to use?
I don’t use spring washers in this application, just plain ones but as Phil mentioned if you use want to use spring washers put the plain ones on first.
Re: Which Loctite threadlock to use?
Thanks Phil and Les - it's so useful to learn from those more experienced than me.