Head gasket failure-3rd in 2½ years
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
For my 1380cc comp engine I have fitted an oil/coolant intercooler. As the seals for the MG Metro intercooler are no longer available I am using a Peugeot oil/coolant intercooler which is similar to the MG Metro item and for which parts are still available.
The oil intercooler is better in some ways to the straight oil cooler in that when the engine is cold the oil warms up quicker and when the engine is hot heat is transferred to the coolant and dispersed through the radiator. Coolant comes from the heater outlet on the rear of the head to the intercooler and then returns to the radiator to be cooled.
The oil intercooler is better in some ways to the straight oil cooler in that when the engine is cold the oil warms up quicker and when the engine is hot heat is transferred to the coolant and dispersed through the radiator. Coolant comes from the heater outlet on the rear of the head to the intercooler and then returns to the radiator to be cooled.
-
- Minor Legend
- Posts: 1667
- Joined: Thu May 12, 2016 6:33 am
- MMOC Member: No
Re: Head gasket failure-3rd in 2½ years
These days, I would expect a good fully synthetic oil to cope with this duty?
-
- Minor Legend
- Posts: 1377
- Joined: Tue Mar 26, 2013 8:20 pm
- Location: Chelmsford, essex
- MMOC Member: No
Re: Head gasket failure-3rd in 2½ years
I'd be suprised if with a decent oil they need it, they have a pretty large radiator and many far more powerfull vehicles seem to manage without.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
The MG 1275cc Metro (non turbo) was fitted with the oil/water intercooler as it was found that the engine and oil ran hot without the intercooler. Good oil does help but there is an optimum temp for max efficiency of oil. If the oil temp can be kept to the optimum so much the better.
-
- Minor Legend
- Posts: 3635
- Joined: Fri Apr 11, 2008 7:28 pm
- Location: Mansfield, Nottinghamshire.
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
As a postscript to my earlier posts in this topic I have now fitted and oil cooler thermostat to both my cars, Elsie May having been run up to temp and left running successfully with no leaks.
It actually turns out to be a very simple job, one that I'm sure anyone with the inclination (and an oil cooler fitted, like me previously, without one inline) could easily complete.
Best wishes,
Mike.
It actually turns out to be a very simple job, one that I'm sure anyone with the inclination (and an oil cooler fitted, like me previously, without one inline) could easily complete.
Best wishes,
Mike.
1954 Series 2: 4 door: "Sally" -- Back on the ground with (slave) wheels and waiting to be resprayed......
1970 Triumph Herald 1200: "Hetty" -- Driven back from Llangollen in Wales (twice.....)
1970 Triumph Herald 1200: "Hetty" -- Driven back from Llangollen in Wales (twice.....)
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
Well done.
I hope that oil pipe is not anywhere near that lever arm castellated nut.
Phil
I hope that oil pipe is not anywhere near that lever arm castellated nut.
Phil
-
- Minor Legend
- Posts: 3635
- Joined: Fri Apr 11, 2008 7:28 pm
- Location: Mansfield, Nottinghamshire.
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
Point noted Phil, however I haven't secured it in place yet, as I'm still pondering exactly how I want to do this....I hope that oil pipe is not anywhere near that lever arm castellated nut.
Best wishes,
Mike.
1954 Series 2: 4 door: "Sally" -- Back on the ground with (slave) wheels and waiting to be resprayed......
1970 Triumph Herald 1200: "Hetty" -- Driven back from Llangollen in Wales (twice.....)
1970 Triumph Herald 1200: "Hetty" -- Driven back from Llangollen in Wales (twice.....)
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
A couple of 'P' clips with a rubber inserts.
One on the inlet pipe from the engine and one on the outlet pipe to the oil cooler. Both near the oil thermostat which will then be kept nicely in place.
These are what I have been using:-
https://www.ebay.co.uk/itm/322547600814 ... %3A2334524
To keep the pipes apart but with free runs the 'P' clips can be used back to back with a bolt through the mount hole
One on the inlet pipe from the engine and one on the outlet pipe to the oil cooler. Both near the oil thermostat which will then be kept nicely in place.
These are what I have been using:-
https://www.ebay.co.uk/itm/322547600814 ... %3A2334524
To keep the pipes apart but with free runs the 'P' clips can be used back to back with a bolt through the mount hole
-
- Minor Legend
- Posts: 3635
- Joined: Fri Apr 11, 2008 7:28 pm
- Location: Mansfield, Nottinghamshire.
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
What size did you use? Thanks.
Best wishes,
Mike.
Best wishes,
Mike.
1954 Series 2: 4 door: "Sally" -- Back on the ground with (slave) wheels and waiting to be resprayed......
1970 Triumph Herald 1200: "Hetty" -- Driven back from Llangollen in Wales (twice.....)
1970 Triumph Herald 1200: "Hetty" -- Driven back from Llangollen in Wales (twice.....)
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
-
- Minor Legend
- Posts: 3635
- Joined: Fri Apr 11, 2008 7:28 pm
- Location: Mansfield, Nottinghamshire.
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
Thanks Phil,
Bargain at £3.40 for a pack of 10.
Best wishes,
Mike.
Bargain at £3.40 for a pack of 10.
Best wishes,
Mike.
1954 Series 2: 4 door: "Sally" -- Back on the ground with (slave) wheels and waiting to be resprayed......
1970 Triumph Herald 1200: "Hetty" -- Driven back from Llangollen in Wales (twice.....)
1970 Triumph Herald 1200: "Hetty" -- Driven back from Llangollen in Wales (twice.....)
- ndevans
- Minor Legend
- Posts: 1088
- Joined: Fri Mar 03, 2006 11:56 am
- Location: Bristol, England
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
Head gasket failure timeline. Starting from the bottom:-
Composite gasket, fitted July 2016, lasted ~5000 miles, failed between 2 & 3 cyls Sept 2018.
Copper gasket, fitted July 2019, lasted ~1800 miles, failed between 3 & 4 cyls Nov 2020
Copper gasket, fitted Dec 2020, lasted ~1600 miles, failed between 2 & 3 cyls June 2021.
2nd photo shows the reverse, in the same order.
Composite gasket, fitted July 2016, lasted ~5000 miles, failed between 2 & 3 cyls Sept 2018.
Copper gasket, fitted July 2019, lasted ~1800 miles, failed between 3 & 4 cyls Nov 2020
Copper gasket, fitted Dec 2020, lasted ~1600 miles, failed between 2 & 3 cyls June 2021.
2nd photo shows the reverse, in the same order.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
Thanks for posting the photos of the failed head gaskets.
My conclusion is that you have got problems with the top of the block and/or the face of the cylinder head.
To overcome this repeat head gasket failure I recommend that you have the top of the block and cylinder head face skimmed.
My conclusion is that you have got problems with the top of the block and/or the face of the cylinder head.
To overcome this repeat head gasket failure I recommend that you have the top of the block and cylinder head face skimmed.
- ndevans
- Minor Legend
- Posts: 1088
- Joined: Fri Mar 03, 2006 11:56 am
- Location: Bristol, England
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
I was afraid you'd say that.......philthehill wrote: ↑Fri Jun 11, 2021 8:16 am Thanks for posting the photos of the failed head gaskets.
My conclusion is that you have got problems with the top of the block and/or the face of the cylinder head.
To overcome this repeat head gasket failure I recommend that you have the top of the block and cylinder head face skimmed.
-
- Minor Legend
- Posts: 1667
- Joined: Thu May 12, 2016 6:33 am
- MMOC Member: No
Re: Head gasket failure-3rd in 2½ years
As per PTH, really. Except that I would be carefully checking for flatness - particularly of the deck - before actually having expensive (if not required) machining carried out.
But as I posted earlier, there can be other contributing factors. It would be good to know if the head actually needs/needed skimming.
But as I posted earlier, there can be other contributing factors. It would be good to know if the head actually needs/needed skimming.
Re: Head gasket failure-3rd in 2½ years
My thoughts are that after the first failure, the metal burn between 2 and 3 cylinder either on head or block, maybe both, would progressively get worse, resulting in a string of gasket breakages. If it was flat at the trouble point they could not blow. You wouldn’t get that many faulty gaskets that could be blamed.
- ndevans
- Minor Legend
- Posts: 1088
- Joined: Fri Mar 03, 2006 11:56 am
- Location: Bristol, England
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
No, that's my thoughts, Les. I might put one down to faulty manufacture, or poor quality, but 3, each from different suppliers...... No, there's a deeper problem somewheres.
-
- Minor Legend
- Posts: 1053
- Joined: Tue Nov 08, 2016 3:18 pm
- Location: Manchester ( Damp and Miserable ) and that's just the wife...
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
Torque wrench calibration?
John ;-)
John ;-)
- ndevans
- Minor Legend
- Posts: 1088
- Joined: Fri Mar 03, 2006 11:56 am
- Location: Bristol, England
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
I thought a couple of photos of the top of the block might be in order.
There are clearly defined rings around the bores, this I assume is where the gasket sits. There is quite a lot of oil on there surface of the block-some, at least, drained out of the head when I lifted it off, but I can't discount that some had leaked or somehow found it's way into the join between the block & gasket.
There are clearly defined rings around the bores, this I assume is where the gasket sits. There is quite a lot of oil on there surface of the block-some, at least, drained out of the head when I lifted it off, but I can't discount that some had leaked or somehow found it's way into the join between the block & gasket.
- ndevans
- Minor Legend
- Posts: 1088
- Joined: Fri Mar 03, 2006 11:56 am
- Location: Bristol, England
- MMOC Member: Yes
Re: Head gasket failure-3rd in 2½ years
I can't rule that out. I have two, one is a simple bar and pointer type, that works through the deflection of the bar under load, this is about 7 years old. The other is a click type that is about 30 years old. I've been tending to use the deflection type, as there's less to go wrong with it-the older click type is now uncalibrated, and I'm less inclined to use it-i understand they can go out of calibration if left with the torque setting screw done up.