Rose Taupe Traveller Restoration
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
Hi
Ive made a repair section for the rear seat/floor support area and trimmed and trial fitted the rear floor section today - a good fit - and the floor repair panel is the correct thickness. I trimmed quite a lot from the repair panel as I diddnt need the rear or side upstands.
Im planning to do the repairs under the rear seat support and next to the spring hanger once the car is rolled over. This diddnt look too rusty on the underside but is terribly rusty inside!!
Ive also made 3 new seat brackets which sit under the front floor panels and the seat brackets bolt to.
One of the originals was un rusted and I salvaged all the old Hank Bushes to refit in the new brackets.
Ive also spot welded new cable and brake pipe metal tabs on the underside of the rear floor section in case I forget to do these before welding the floor in.
The next bits I plan to do are the other rear floor section and the o/s front step sill repair.
Here are some pics:
Ive made a repair section for the rear seat/floor support area and trimmed and trial fitted the rear floor section today - a good fit - and the floor repair panel is the correct thickness. I trimmed quite a lot from the repair panel as I diddnt need the rear or side upstands.
Im planning to do the repairs under the rear seat support and next to the spring hanger once the car is rolled over. This diddnt look too rusty on the underside but is terribly rusty inside!!
Ive also made 3 new seat brackets which sit under the front floor panels and the seat brackets bolt to.
One of the originals was un rusted and I salvaged all the old Hank Bushes to refit in the new brackets.
Ive also spot welded new cable and brake pipe metal tabs on the underside of the rear floor section in case I forget to do these before welding the floor in.
The next bits I plan to do are the other rear floor section and the o/s front step sill repair.
Here are some pics:
Last edited by taupe on Wed Aug 30, 2017 10:41 am, edited 1 time in total.
Looking good
How does the upstand bellow the rear seat attach to the floor? I know the floor repair panels are not correct in this area. I've searched & searched, but I can't find anyone who has repaired this area to factory spec. I know we spoke about this briefly when I was over the other week.
BTW, no offence, but if you want to get 30% off a new digi camera, go to www.fuji.co.uk/shop and use promo code P832A4V3T8WKG
How does the upstand bellow the rear seat attach to the floor? I know the floor repair panels are not correct in this area. I've searched & searched, but I can't find anyone who has repaired this area to factory spec. I know we spoke about this briefly when I was over the other week.
BTW, no offence, but if you want to get 30% off a new digi camera, go to www.fuji.co.uk/shop and use promo code P832A4V3T8WKG
Hi Rich
Wait and see!
Sorry about the awful pic quality - I do have a digi camera but cant find the USB cable and disc!!!
The vertical seat support panel at the back of the rear floor has a 1/2" return at the bottom facing forwards. This was originally spotwelded to the floor pan and sides of the step sills and gas welded at the bottom corners of the step sill. This is the bit in my fuzzy first and second photos!!
The spring hangers front edges also sit under this seam and have 2 hot rivets right thro the floor and the 1/2" return on either side. I havent ground the rivet heads off yet but I am guessing 3/16" or 1/4" rivets were used.
The rear of the spring hanger also has two hot rivets each side. The two inner ones go thro the floor pan and the 1/2" rear facing return of the seat support. The outer two go through the floor pan and the 3/4"return on the side chassis rail (rear extension of the step sill). Incidentally this helps a lot with alignment of the spring hangers.
Im going to tackle the repair when the shell is rolled but I intend to replace the section of floor pan under the seat support and the spring hanger plate first before finally welding in the rear floor panel - Im going to extend the front edge of the under seat floor repair to bring it to about 3mm before the rear floor pan starts and spot weld it in place along the 1/2" return 'as original'. This will allow the rear floor pan to sit on the outer edge of the 1/2" return and I will then seam weld it from underneath.
At the sides I will spot weld the spring hanger plate to this return but it will sit further forward, part way into the rear floor pan which I will cut out and seam weld to suit. Once this is done I will drill and fit the hot rivets or I might just plug weld right thro.
I expect it will be a few weeks before I tackle this and post pics so if you need to come over I can show you!!
Regards
Taupe
Wait and see!
Sorry about the awful pic quality - I do have a digi camera but cant find the USB cable and disc!!!
The vertical seat support panel at the back of the rear floor has a 1/2" return at the bottom facing forwards. This was originally spotwelded to the floor pan and sides of the step sills and gas welded at the bottom corners of the step sill. This is the bit in my fuzzy first and second photos!!
The spring hangers front edges also sit under this seam and have 2 hot rivets right thro the floor and the 1/2" return on either side. I havent ground the rivet heads off yet but I am guessing 3/16" or 1/4" rivets were used.
The rear of the spring hanger also has two hot rivets each side. The two inner ones go thro the floor pan and the 1/2" rear facing return of the seat support. The outer two go through the floor pan and the 3/4"return on the side chassis rail (rear extension of the step sill). Incidentally this helps a lot with alignment of the spring hangers.
Im going to tackle the repair when the shell is rolled but I intend to replace the section of floor pan under the seat support and the spring hanger plate first before finally welding in the rear floor panel - Im going to extend the front edge of the under seat floor repair to bring it to about 3mm before the rear floor pan starts and spot weld it in place along the 1/2" return 'as original'. This will allow the rear floor pan to sit on the outer edge of the 1/2" return and I will then seam weld it from underneath.
At the sides I will spot weld the spring hanger plate to this return but it will sit further forward, part way into the rear floor pan which I will cut out and seam weld to suit. Once this is done I will drill and fit the hot rivets or I might just plug weld right thro.
I expect it will be a few weeks before I tackle this and post pics so if you need to come over I can show you!!
Regards
Taupe
Rich
Heres a couple of pages detailing the floor make up - the front rivet holes can be seen in the second image just above and left of No.44 in the middle of the pic
Regards
Taupe
Heres a couple of pages detailing the floor make up - the front rivet holes can be seen in the second image just above and left of No.44 in the middle of the pic
Regards
Taupe
Last edited by taupe on Wed Aug 30, 2017 10:42 am, edited 1 time in total.
This guy is Chip Foose, not David Baileyrich-legg wrote: BTW, no offence, but if you want to get 30% off a new digi camera, go to www.fuji.co.uk/shop and use promo code P832A4V3T8WKG
[sig]8426[/sig]
Compare the Minors - Simples !! http://mog.myfreeforum.org/index.php
Compare the Minors - Simples !! http://mog.myfreeforum.org/index.php
Hi
Ive finished the o/s inner step sill tonight and started preparing the side underfloor sections for fitting.
The repair panels diddnt come with the drain points so I cut a slot with a dremel disc, heated the panel and hammered the points in with a 1" steel rod.
The next bit to fabricate is the front of the drivers floor support and a section at the bottom of the front wheelarch. Then Im going to start on the n/s rear floor.
Here are some pics:
Ive finished the o/s inner step sill tonight and started preparing the side underfloor sections for fitting.
The repair panels diddnt come with the drain points so I cut a slot with a dremel disc, heated the panel and hammered the points in with a 1" steel rod.
The next bit to fabricate is the front of the drivers floor support and a section at the bottom of the front wheelarch. Then Im going to start on the n/s rear floor.
Here are some pics:
Last edited by taupe on Wed Aug 30, 2017 10:42 am, edited 1 time in total.
Hi
Thanks for the comments, it helps with motivation!
Here is an update.
I made a repair section for the front of the drivers floor/toeboard joint first.
I then cut out and trial fitted the n/s rear floor, made a repair for the rear seat support and rear step sill section.
Lastly I put the bolts in the n/s floor for the exhaust heatshield.
In all a good days progress!!
Here are some pics :
Thanks for the comments, it helps with motivation!
Here is an update.
I made a repair section for the front of the drivers floor/toeboard joint first.
I then cut out and trial fitted the n/s rear floor, made a repair for the rear seat support and rear step sill section.
Lastly I put the bolts in the n/s floor for the exhaust heatshield.
In all a good days progress!!
Here are some pics :
Last edited by taupe on Wed Aug 30, 2017 10:44 am, edited 1 time in total.
-
- Minor Friendly
- Posts: 21
- Joined: Wed Jun 16, 2004 7:39 pm
- Location: Shipley
- MMOC Member: No
-
- Minor Addict
- Posts: 771
- Joined: Tue Aug 11, 2009 5:53 pm
- MMOC Member: No
Hi
Ive been looking at the sill components needed to extend out from the floors.
Ive got Hadrian repair panels for the floor edge panels. These seem to be pretty good, thickness and fit wise - and now have the drain holes in as my previous post.
Ive looked at the boxing panels (the long ones with big holes all along) and the boxing extension panel, one of each came with the car when I bought it.
I decided that I could make the extension panel (originally with a big rectangular hole) as I only need to replace the bottom half of this panel up to the top edge of the step sill flange.
The new panel has one circular hole and was a little too long - it was also without a seperate infill panel between the seat base and B pillar - this was all built in as one panel and a strange shape at the top? I worked out the sizes after a lot of fiddling about/measuring of what was left of the original.
Once Id realised that the missing bottom edge/flange should be level and in line with the bottom edge of the boxing panel ( mine was rather bodged in this area and tilted upwards on one side and down on the other!) - it seemed obvious afterwards - and it was quite straightforward.
To make the panel I started by cutting out a rectangular hole in some 3mm steel, then cut a matching plate 2.5 mm smaller to act as a press tool. After cutting some big holes in the new panel to make the pressing easier, the 'tool' was then simply aligned and the plate pressed into the hole. - very satisfying results
The main long boxing panel Ive got is only 18 swg and the original was 16 swg so Im thinking about whether I need to make these too!!
I must buy the other outer floor panel that I need for the offside. Im going to use one from a two door and cut it down to match the one for the nearside Ive already done.
Here are some pics:
Ive been looking at the sill components needed to extend out from the floors.
Ive got Hadrian repair panels for the floor edge panels. These seem to be pretty good, thickness and fit wise - and now have the drain holes in as my previous post.
Ive looked at the boxing panels (the long ones with big holes all along) and the boxing extension panel, one of each came with the car when I bought it.
I decided that I could make the extension panel (originally with a big rectangular hole) as I only need to replace the bottom half of this panel up to the top edge of the step sill flange.
The new panel has one circular hole and was a little too long - it was also without a seperate infill panel between the seat base and B pillar - this was all built in as one panel and a strange shape at the top? I worked out the sizes after a lot of fiddling about/measuring of what was left of the original.
Once Id realised that the missing bottom edge/flange should be level and in line with the bottom edge of the boxing panel ( mine was rather bodged in this area and tilted upwards on one side and down on the other!) - it seemed obvious afterwards - and it was quite straightforward.
To make the panel I started by cutting out a rectangular hole in some 3mm steel, then cut a matching plate 2.5 mm smaller to act as a press tool. After cutting some big holes in the new panel to make the pressing easier, the 'tool' was then simply aligned and the plate pressed into the hole. - very satisfying results
The main long boxing panel Ive got is only 18 swg and the original was 16 swg so Im thinking about whether I need to make these too!!
I must buy the other outer floor panel that I need for the offside. Im going to use one from a two door and cut it down to match the one for the nearside Ive already done.
Here are some pics:
Last edited by taupe on Wed Aug 30, 2017 10:45 am, edited 1 time in total.
Re: Rose Taupe Traveller Restoration- update 16
Hi
Just a mini update on progress.
Its been rather cold for doing metalwork so I have been getting on with a few ancillaries such as replacing the heater seals, overhauling switches etc. I did however make up two cover panels for the underside of the timber just behind the B post. These are pretty much as the repair panels available but do have the upturned tab into the rear wheel arch which sits under the rear wing and closes the gap between wing and timber at the bottom.
Ive nearly finished making my heavy duty front end alignment jig - Im itching to get the car rolled over now. Ive used ground flat steel for the main reference members as I want to ensure accuracy and bright steel plate is often a bit out of true. Its been quite challenging marking out, drilling etc to the accuracy required with dimensions such as 12.437" , 13.312" etc required to be attained - so its been out with the vernier calipers etc. I guess its not actually that critical as long as its all nice and square and I dont allow multiple measurements each out by a fraction to add up to say as much as 0.5mm out.! There is some tolerence built into the fixture any way.
I guess theres no point having an alignment jig if its out of alignment before you start.
Ive turned up the lower suspension eye checking bushes in bronze and pressed them in to the lower jig tube and now have a good fit with the steel checking pins - these check the eyebolt holes in the main chassis legs and are critical to the steering geometry. Normally you would ensure this by carefully marking and taking check dimensions before removing the old chassis leg but if the front end has been bashed or the eye rotted right out then its just guesswork without a jig.
The main sides of the jig are detailed to be 1/4 plate but cutting this to the required accuracy was going to be very difficult and time consuming so Ive opted for 1.5mm steel and reinforced with 2x2x1/4 angle. It should end up a lot stronger than the 1/4 plate anyway. Ill be posting some pics as soon as its finished. This is what im aiming for:
Ive tidied up the wiring harness which was in surprisingly good condition and just needed a couple of short lengths of damaged wire replacing.
Im considering having the run to the back of the car rebraided by Autosparks as detailed in another post under Electrical or might just use self amalg tape.
Sorry no pics at the moment - will post some more soon....
Just a mini update on progress.
Its been rather cold for doing metalwork so I have been getting on with a few ancillaries such as replacing the heater seals, overhauling switches etc. I did however make up two cover panels for the underside of the timber just behind the B post. These are pretty much as the repair panels available but do have the upturned tab into the rear wheel arch which sits under the rear wing and closes the gap between wing and timber at the bottom.
Ive nearly finished making my heavy duty front end alignment jig - Im itching to get the car rolled over now. Ive used ground flat steel for the main reference members as I want to ensure accuracy and bright steel plate is often a bit out of true. Its been quite challenging marking out, drilling etc to the accuracy required with dimensions such as 12.437" , 13.312" etc required to be attained - so its been out with the vernier calipers etc. I guess its not actually that critical as long as its all nice and square and I dont allow multiple measurements each out by a fraction to add up to say as much as 0.5mm out.! There is some tolerence built into the fixture any way.
I guess theres no point having an alignment jig if its out of alignment before you start.
Ive turned up the lower suspension eye checking bushes in bronze and pressed them in to the lower jig tube and now have a good fit with the steel checking pins - these check the eyebolt holes in the main chassis legs and are critical to the steering geometry. Normally you would ensure this by carefully marking and taking check dimensions before removing the old chassis leg but if the front end has been bashed or the eye rotted right out then its just guesswork without a jig.
The main sides of the jig are detailed to be 1/4 plate but cutting this to the required accuracy was going to be very difficult and time consuming so Ive opted for 1.5mm steel and reinforced with 2x2x1/4 angle. It should end up a lot stronger than the 1/4 plate anyway. Ill be posting some pics as soon as its finished. This is what im aiming for:
Ive tidied up the wiring harness which was in surprisingly good condition and just needed a couple of short lengths of damaged wire replacing.
Im considering having the run to the back of the car rebraided by Autosparks as detailed in another post under Electrical or might just use self amalg tape.
Sorry no pics at the moment - will post some more soon....
Last edited by taupe on Wed Aug 30, 2017 10:46 am, edited 1 time in total.