Search found 10700 matches

by philthehill
Thu Mar 28, 2024 10:59 pm
Forum: Parts for sale
Topic: Marina disc brakes on Minor swivelos
Replies: 0
Views: 5

Marina disc brakes on Minor swivelos

May be of interest:- https://www.ebay.co.uk/itm/176301431942?itmmeta=01HT3MC4TQCER11WEE3Z7JGMB3&hash=item290c625c86:g:~ZEAAOSwxMVl~zkW&itmprp=enc%3AAQAJAAAA8CO5ZQmZg%2Fidm%2FOFuQznwu0I51QCChGFLhUuoomaYN7dJaauahvxqnIHlvkrCi9V%2B0bTs7jHJmD6UlpI%2FdFY19AhSo4N8CFKBnt2zArpM6zkqoIfaDQcDTAuBsj5BJUf...
by philthehill
Thu Mar 28, 2024 9:03 am
Forum: Mechanical
Topic: standard 1098 engine
Replies: 11
Views: 267

Re: standard 1098 engine

Only if the distance between the extreme edges of the damage is less than 2.64125" diameter would you be able to fit a cylinder liner. See section AAA.12 of Morris Minor 1000 workshop manual AKD 530. If the damage distance is more than that quoted above the remaining damage will still be expose...
by philthehill
Wed Mar 27, 2024 4:33 pm
Forum: Parts for sale
Topic: Where can I buy a new bonnet rubber
Replies: 8
Views: 155

Re: Where can I buy a new bonnet rubber

If your windscreen is leaking just flood the seal with Captain Tolley's creeping crack cure. https://www.ebay.co.uk/itm/126024991251?epid=2306096349&itmmeta=01HT0C6SF64B8E5BWXH1BZNK3P&hash=item1d57acc213:g:USsAAOSwEmNk6xWi&itmprp=enc%3AAQAJAAAA0NVn%2BegO9A2Ieq16dmWugHWFYjM3LD%2FhicvHMtAY...
by philthehill
Mon Mar 25, 2024 12:27 pm
Forum: Other
Topic: Water temperature switch
Replies: 8
Views: 165

Re: Water temperature switch

It will be much easier to fit a coolant temp gauge than try and improvise what you want.
If you want the light to illuminate when the engine is overheated it will be too late. With a gauge you will know what the temp is and can observe it rising and stop the engine before the engine gets damaged.
by philthehill
Sun Mar 24, 2024 9:13 am
Forum: Mechanical
Topic: Hub identification disc brakes
Replies: 7
Views: 179

Re: Hub identification disc brakes

Below is a Marina/Ital stub axle fitted to a Minor swivel. Marina stub axle.JPG The hub nut locking arrangement is different - note the splines onto which a internal splined washer fits, the hub nut does not have any castellation's and is locked by a special locking washer which is secured by a spli...
by philthehill
Sat Mar 23, 2024 9:46 pm
Forum: Mechanical
Topic: Hub identification disc brakes
Replies: 7
Views: 179

Re: Hub identification disc brakes

Bill
What ever the grade those bolts with washers are I would advise that they need to be replaced with the correct bolts & without washers and correctly torqued.
Phil
by philthehill
Sat Mar 23, 2024 4:15 pm
Forum: Mechanical
Topic: Hub identification disc brakes
Replies: 7
Views: 179

Re: Hub identification disc brakes

The hubs are Marina/Mr Grumpys with the 3.75"Marina PCD revised to 4" I have the same hubs on my Minor. Grumpy hub 2.jpg The hub bearings should be taper adjustable bearings not parallel. Do you have the stub axle adapter sleeve fitted which fits over the stub axle and allows the appropria...
by philthehill
Fri Mar 22, 2024 8:38 am
Forum: Parts for sale
Topic: VENT PIPE
Replies: 9
Views: 255

Re: VENT PIPE

I would be looking for around 150 psi.
by philthehill
Thu Mar 21, 2024 8:03 pm
Forum: General Discussion
Topic: Spax part numbers
Replies: 2
Views: 116

Re: Spax part numbers

The number stamped on the SPAX gas adjustable damper body as supplied as part of a SPAX gas damper conversion kit for the front and rear of a Minor is G7364AO.
by philthehill
Thu Mar 21, 2024 7:27 pm
Forum: Parts for sale
Topic: VENT PIPE
Replies: 9
Views: 255

Re: VENT PIPE

I do have the SU Reference Catalogue. Burlen Fuels ALT9524, Issue 12/4, December 1998. It states for a 1098cc 'A' Series engine fitted with a AUD 13 carb the needle should be AUD1478AN. The catalogue does not give a listing for the HS2 carb when the PCV valve is fitted/used or for the HS2 carb with ...
by philthehill
Thu Mar 21, 2024 5:35 pm
Forum: Parts for sale
Topic: VENT PIPE
Replies: 9
Views: 255

Re: VENT PIPE

The manifold in the photo above is the early 2 piece manifold for a H2 SU carb. There is no provision for either a PCV valve or servo vacuum take off. The manifold appears to have been drilled and tapped for a vacuum pipe take off. Only the later manifolds have provision for the PCV valve and servo ...
by philthehill
Thu Mar 21, 2024 5:19 pm
Forum: Other
Topic: What is this overflow? pipe for?
Replies: 3
Views: 182

Re: What is this overflow? pipe for?

The idea is that as the pipe exit is low and in the under car depression slipstream and any fumes are meant to be sucked out of the engine and dispersed into the atmosphere. Not very environmentally friendly . Later cars had the breathers piped into the inlet tract and any fumes generated were consu...
by philthehill
Thu Mar 21, 2024 5:08 pm
Forum: General Discussion
Topic: Classic Machine Shop recon block
Replies: 6
Views: 320

Re: Classic Machine Shop recon block

https://www.classicmachineshop.co.uk/
They are just outside Nottingham - where are you?
At the moment have not found any reviews but they may be there somewhere.
by philthehill
Wed Mar 20, 2024 8:41 pm
Forum: Mechanical
Topic: Rear damper link rubber top bush
Replies: 4
Views: 182

Re: Rear damper link rubber top bush

Make a note of the part numbers as a supplement in your Army Minor parts list then you will have a record of the alternative bushes available.
Phil
by philthehill
Wed Mar 20, 2024 12:43 pm
Forum: Mechanical
Topic: Steering column pinch bolt problem
Replies: 6
Views: 198

Re: Steering column pinch bolt problem

Well done. :tu1:
The correct bolt for this application is 1/4" BSF bolt but a 1/4" UNF bolt or in my case I have fitted a 12.9 high tensile UNF cap headed bolt.
by philthehill
Wed Mar 20, 2024 12:10 pm
Forum: Mechanical
Topic: Rear damper link rubber top bush
Replies: 4
Views: 182

Re: Rear damper link rubber top bush

Photo of rear damper link bushes below. 1. ESM damper link Pt No: SUS702 with fitted one piece rubber bush. Note: The rubber bush has been removed from the top eye. The ESM bush was removed for use in the top eye of a gas tele damper conversion kit so as to be able to utilise the damper chassis moun...
by philthehill
Tue Mar 19, 2024 7:10 pm
Forum: Mechanical
Topic: Steering column pinch bolt problem
Replies: 6
Views: 198

Re: Steering column pinch bolt problem

Have you lined up the hole in the column with the waisted section of the rack pinion? With all lined up the bolt will pass easily though the column and past the waisted section of the pinion. If you have a shallow taper punch put it into the hole and wiggle it about and that should line everything u...
by philthehill
Tue Mar 19, 2024 6:56 pm
Forum: Mechanical
Topic: Rear damper link rubber top bush
Replies: 4
Views: 182

Rear damper link rubber top bush

If you are having to replace the rear suspension damper top link bush (the one that fits onto the chassis pin) forget the two piece rubber bushes or a poly bush and fit a classic Mini suspension damper bush Pt No: 21A1230. If you can find them bush 21A503 is even better. 21A503 is also a one piece b...