About a week
Search found 470 matches
- Thu Jul 06, 2023 11:39 pm
- Forum: Mechanical
- Topic: Rear Suspension Overhaul Advice please
- Replies: 73
- Views: 259691
- Thu Jul 06, 2023 8:33 pm
- Forum: Mechanical
- Topic: Rear Suspension Overhaul Advice please
- Replies: 73
- Views: 259691
Re: Rear Suspension Overhaul Advice please
They were £350 last year.
- Thu Jul 06, 2023 8:25 pm
- Forum: Mechanical
- Topic: Rear Suspension Overhaul Advice please
- Replies: 73
- Views: 259691
Re: Rear Suspension Overhaul Advice please
I changed my springs last year with a set from a usual supplier, they lasted about two months before the bump stops hit the pad over any bump. I contacted Jones springs who made me a set to the original specification, they cost quite a bit more but are worth it. The others at the back of my workshop...
- Tue Jun 27, 2023 3:16 pm
- Forum: Mechanical
- Topic: Oil pressure reading too high?
- Replies: 17
- Views: 2854
Re: Oil pressure reading too high?
What type of oil are you using?
- Wed May 17, 2023 5:31 pm
- Forum: General Discussion
- Topic: Ran out of fuel, now have issues.
- Replies: 21
- Views: 3652
Re: Ran out of fuel, now have issues.
Sorry, I didn't spot that. I would be tempted to put a set of points and condenser on it then try again.
- Wed May 17, 2023 4:52 pm
- Forum: General Discussion
- Topic: Ran out of fuel, now have issues.
- Replies: 21
- Views: 3652
Re: Ran out of fuel, now have issues.
While you are messing with the distributor, try a new condenser.
- Thu May 11, 2023 10:18 pm
- Forum: Mechanical
- Topic: Valve sizes
- Replies: 5
- Views: 453
Re: Valve sizes
The blanking plugs are quite difficult to remove, I found that the best way is to weld a wheel nut to it and then use a long breaker bar.
- Wed May 03, 2023 4:31 pm
- Forum: Mechanical
- Topic: Help
- Replies: 3
- Views: 483
Re: Help
how old is the fuel? Also check the points and condenser.
- Tue Mar 28, 2023 4:42 pm
- Forum: Mechanical
- Topic: Cold start Yes - Hot start No! Asdvice sought please.
- Replies: 36
- Views: 5800
Re: Cold start Yes - Hot start No! Asdvice sought please.
Check the compression when cold then check again when hot.
- Tue Feb 07, 2023 9:33 am
- Forum: Mechanical
- Topic: gearbox bearing shims
- Replies: 23
- Views: 1921
Re: gearbox bearing shims
If you heat a magnet to its ignition point (cherry red) it will lose all of its magnetism. I would be tempted to silver solder rather than braze as its cooler.
- Sat Feb 04, 2023 4:50 pm
- Forum: Mechanical
- Topic: gearbox bearing shims
- Replies: 23
- Views: 1921
Re: gearbox bearing shims
Sorry I should have read the thread properly, Kevin has already stated he has read the Dorset guide and philthehill has already answered the shim question!!
- Sat Feb 04, 2023 9:43 am
- Forum: Mechanical
- Topic: gearbox bearing shims
- Replies: 23
- Views: 1921
Re: gearbox bearing shims
I assume that you have read this from the Dorset branch? https://www.dorsetmmoc.co.uk/wordpress/tech_articles/gearboxrebuild.pdf If so, are you referring to the shims at figure 5? If so the shims are there to take up any play due to the tolerance from the machining of the front and rear cover. They ...
- Wed Dec 28, 2022 12:06 pm
- Forum: Mechanical
- Topic: Rough idling on 1967 Minor
- Replies: 19
- Views: 1999
Re: Rough idling on 1967 Minor
E10 petrol? Gummed up jet? I would be tempted to take it for a good run and then see how it goes.
- Wed Dec 28, 2022 12:03 pm
- Forum: Mechanical
- Topic: Rough idling on 1967 Minor
- Replies: 19
- Views: 1999
Re: Rough idling on 1967 Minor
E10 petrol?
- Fri Dec 23, 2022 2:21 pm
- Forum: General Discussion
- Topic: Wheel spacers
- Replies: 3
- Views: 347
Re: Wheel spacers
Are you fitting alloys? if so I'm pretty sure ESM sell them, they are about 5mm thick and move the wheel out just far enough to miss the suspension. You only need to fit them on the front. You may also consider fitting longer wheel studs. https://www.morrisminorspares.com/wheels-tyres-c94/wheels-tyr...
- Thu Dec 22, 2022 3:56 pm
- Forum: Bodywork
- Topic: Boot Lock does not lock handle
- Replies: 15
- Views: 7307
Re: Boot Lock does not lock handle
Are you sure that it's not been fitted upside down into the boot?
- Thu Dec 15, 2022 4:03 pm
- Forum: Electrical
- Topic: Accuspark POSITIVE earth kit Installation
- Replies: 32
- Views: 2568
Re: Accuspark POSITIVE earth kit Installation
Svenedin, a good job but the plastic cap for the Lucar terminal is on the wrong way round.
- Tue Dec 13, 2022 3:32 pm
- Forum: Electrical
- Topic: Battery selection
- Replies: 11
- Views: 5851
Re: Battery selection
This should be a sticky kept at the top of the page.
- Thu Dec 08, 2022 4:36 pm
- Forum: Electrical
- Topic: Slow churning starter motors
- Replies: 7
- Views: 655
Re: Slow churning starter motors
Is the ignition timing too far advanced?
- Sun Dec 04, 2022 3:50 pm
- Forum: Mechanical
- Topic: Midget disks
- Replies: 3
- Views: 465
Re: Midget disks
The disk on the left is for steel wheels the disk on the right is for wire wheels when fitted to a midget. The only difference is the hight.