Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Oooh - have I missed something here?
You're using Escort hubs - how do these fit to the Morris spindles?
And why Princess calipers? They're big that I remember but wouldn't newer calipers be more up to date and easier to find spares for?
Cheers - loving the build.
Martin
You're using Escort hubs - how do these fit to the Morris spindles?
And why Princess calipers? They're big that I remember but wouldn't newer calipers be more up to date and easier to find spares for?
Cheers - loving the build.
Martin
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Finished the assembly of the Princess 4 pot callipers, learnt a few cool hacks too.
Too assemble you need a piece of 42mm dia waste tube, some super glue and don’t sink the piston down too far.
1 clean the piston cavity, make good and use light oil
2. Add lower seal only, then insert piston about halfway.
3. Then fit the seal into the metal outer seal first, carefully drop down over the piston until just above the seal ring, then get plastic tube a lightly tap down until set.
4. If the seal pops out, and it will glue the seal into the metal ring with superglue, sorted.....
Both sorted and torqued up, awaiting pads and new stainless cables, until then back in a bag and in box.
Too assemble you need a piece of 42mm dia waste tube, some super glue and don’t sink the piston down too far.
1 clean the piston cavity, make good and use light oil
2. Add lower seal only, then insert piston about halfway.
3. Then fit the seal into the metal outer seal first, carefully drop down over the piston until just above the seal ring, then get plastic tube a lightly tap down until set.
4. If the seal pops out, and it will glue the seal into the metal ring with superglue, sorted.....
Both sorted and torqued up, awaiting pads and new stainless cables, until then back in a bag and in box.
- Attachments
-
- 6D15249A-4439-4039-8EDB-FD158E916C2B.jpeg (3.16 MiB) Viewed 2811 times
-
- 1A845E3F-47BC-42D1-9DAA-50745A6DD8C9.jpeg (2.92 MiB) Viewed 2811 times
-
- 497919F0-619A-4EE8-A587-8A0BCDA785E8.jpeg (2.51 MiB) Viewed 2811 times
-
- 0D66165A-2F38-42EE-860D-B1CA705B7BAA.jpeg (2.29 MiB) Viewed 2811 times
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Yep used old steel escort mk2 hubs, but going escort mk2 rs2000 rally gp4 hubs, they need two shims, keeps all escort bearings which are better. Princess because I’ve had them, they’re period correct , yes they heavy and cost a lot to refurb, Wilwood would have been cheaper in the long run, they do fit, with 2-3mm clearance , glad your enjoying the build.happy to take photo of complete assembly,( hubs and old disc un-drilled) will be for sale soon, if interested.Nourish wrote: ↑Thu May 13, 2021 11:07 pm Oooh - have I missed something here?
You're using Escort hubs - how do these fit to the Morris spindles?
And why Princess calipers? They're big that I remember but wouldn't newer calipers be more up to date and easier to find spares for?
Cheers - loving the build.
Martin
Last edited by fixwheelmad on Sat May 15, 2021 7:49 pm, edited 1 time in total.
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Some pretty bits awaiting my atlas axle, which is finished sooner than I thought. Will set up with drums and replace with disc setup later.
Discs and callipers, awaiting painted struts, new ally hubs and fitting, back in a box until next needed.
Discs and callipers, awaiting painted struts, new ally hubs and fitting, back in a box until next needed.
- Attachments
-
- 5648F24F-88C0-4C69-A5F1-F7B7B4BD6A48.jpeg (2.63 MiB) Viewed 2809 times
-
- B8385E0F-3BD4-4200-9E2F-DE9ADE35E278.jpeg (2.49 MiB) Viewed 2809 times
-
- A1DC3385-E8FC-4724-B2DE-5D61845100C0.jpeg (2.35 MiB) Viewed 2809 times
-
- 73EE51AB-9442-4852-AE46-13E0A9210D9C.jpeg (2.55 MiB) Viewed 2809 times
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Due to interest, some images of break setup, clearances and tolerances
- Attachments
-
- B9E103A3-C25B-4072-9E93-BE134A638161.jpeg (2.35 MiB) Viewed 2808 times
-
- 0AF72A1E-55AA-40C5-A056-0195D297A84A.jpeg (2.01 MiB) Viewed 2808 times
-
- F2B0FB67-4F19-47FB-81E9-593E65503097.jpeg (2.76 MiB) Viewed 2808 times
-
- EC445B5C-9808-403C-BAD7-A3C079A8731C.jpeg (2.57 MiB) Viewed 2808 times
-
- 71C72DC4-F7C6-4AAA-869D-E972FF61572E.jpeg (2.53 MiB) Viewed 2808 times
-
- Minor Maniac
- Posts: 10794
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Observation:-
You have only two 3/8" bolts holding the calliper to the swivel yet you have increased the braking efficiently which will put a high shear loading on those two bolts not withstanding the loading on the swivel brake mount.
Are you intending to increase the number of calliper fixing bolts?
Phil
You have only two 3/8" bolts holding the calliper to the swivel yet you have increased the braking efficiently which will put a high shear loading on those two bolts not withstanding the loading on the swivel brake mount.
Are you intending to increase the number of calliper fixing bolts?
Phil
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Ah - so when you say shims do you really mean collars? - you're adjusting the diameters and not the lateral position?
Got any dimensions - please?
I posted some drawings on the other side some while ago of the stub axles I made up to fit Vitesse hubs when I was an apprentice - could alter these drawings to do a permanent job.
https://www.morrisminorowners.co.uk/vie ... it=vitesse
Got any dimensions - please?
I posted some drawings on the other side some while ago of the stub axles I made up to fit Vitesse hubs when I was an apprentice - could alter these drawings to do a permanent job.
https://www.morrisminorowners.co.uk/vie ... it=vitesse
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Philphilthehill wrote: ↑Sat May 15, 2021 8:41 pm Observation:-
You have only two 3/8" bolts holding the calliper to the swivel yet you have increased the braking efficiently which will put a high shear loading on those two bolts not withstanding the loading on the swivel brake mount.
Are you intending to increase the number of calliper fixing bolts?
Phil
Phil
I ran this setup 20 years ago, driving hard with a 1.6 then a 2.0 TC no issues, I not your concerns but once all bolts are high tensile there is no issues. And I will be driving hard this time, eventually I will replace with escort struts which are on my bench atm, but that’s a few more hours away.
Eugene
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
I’ve got your images, I will take photos of the setup with dimensions, from spindle through to nut ok.Nourish wrote: ↑Sat May 15, 2021 10:15 pm Ah - so when you say shims do you really mean collars? - you're adjusting the diameters and not the lateral position?
Got any dimensions - please?
I posted some drawings on the other side some while ago of the stub axles I made up to fit Vitesse hubs when I was an apprentice - could alter these drawings to do a permanent job.
https://www.morrisminorowners.co.uk/vie ... it=vitesse
-
- Minor Maniac
- Posts: 10794
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Thank you for the reply.
Whilst you may have run this set up with no problems I am not convinced that it is the correct or proper way of mounting the calliper.
When BL fitted disc brakes to the Marina swivel which is similar to the Minor it utilised the four 3/8" holes with a wrap round mount bracket secured with four high tensile bolts. Even with new high tensile bolts you have reduced the holding ability by 50% and at the same time increased the loading on the mount bolts and swivel with the use of more powerful brakes.
Phil
Whilst you may have run this set up with no problems I am not convinced that it is the correct or proper way of mounting the calliper.
When BL fitted disc brakes to the Marina swivel which is similar to the Minor it utilised the four 3/8" holes with a wrap round mount bracket secured with four high tensile bolts. Even with new high tensile bolts you have reduced the holding ability by 50% and at the same time increased the loading on the mount bolts and swivel with the use of more powerful brakes.
Phil
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Philphilthehill wrote: ↑Sun May 16, 2021 8:21 am Thank you for the reply.
Whilst you may have run this set up with no problems I am not convinced that it is the correct or proper way of mounting the calliper.
When BL fitted disc brakes to the Marina swivel which is similar to the Minor it utilised the four 3/8" holes with a wrap round mount bracket secured with four high tensile bolts. Even with new high tensile bolts you have reduced the holding ability by 50% and at the same time increased the loading on the mount bolts and swivel with the use of more powerful brakes.
Phil
Like the image shown on John B website, noted will mock one up....
Thanks
- Attachments
-
- 37E8062D-DB27-4761-A428-0028B5D4DC3A.jpeg (197.75 KiB) Viewed 2777 times
-
- Minor Maniac
- Posts: 10794
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Update on the small moulding, anyone interested stop playing with glass fibre! I used a new all in one kit from easy composites, and well it was easy. Clean the product, tape up holes, wax on and off 10 tens, apply release, add two gel coat layers , when tacky mix paste and hardener, slepe on and push into all corners. Allow 24 hours to dry, pull out plug and clean mould.
Items I cast where, steering wheel bezel, door pull bezel, rear number plate light, suspension damper top cap and trafficators blanks.
These will be made in aqua clear resin and carbon weave, other bigger items I might attempt or farm out. Will do some tests when weather is a little warmer.
BTW the grey dino turds are the mold putty, its a mix of very finally chopped fiber, and fiber filler and the mixed in hardner
Items I cast where, steering wheel bezel, door pull bezel, rear number plate light, suspension damper top cap and trafficators blanks.
These will be made in aqua clear resin and carbon weave, other bigger items I might attempt or farm out. Will do some tests when weather is a little warmer.
BTW the grey dino turds are the mold putty, its a mix of very finally chopped fiber, and fiber filler and the mixed in hardner
- Attachments
-
- 56303474-A86C-4DA9-BB42-76DC80384BA3.jpeg (3.24 MiB) Viewed 2749 times
-
- 3D466683-68FF-455C-BE42-6067D9469422.jpeg (3.12 MiB) Viewed 2749 times
-
- 40A64401-00E4-4FC6-9E39-52BF5D990C93.jpeg (1.95 MiB) Viewed 2749 times
-
- F9F99DF3-D35C-4D26-BD44-8B1D4B73F8DE.jpeg (2.57 MiB) Viewed 2749 times
-
- B6E6471B-8CE9-4A79-BB3E-359CD446E511.jpeg (1.85 MiB) Viewed 2749 times
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Phil
Going to fab out of some 10mm I have and check tolerances, but I think you’ll agree a vast improvement .
- Attachments
-
- A1B319BF-63C7-408F-B19F-31AB3A820C8C.jpeg (3.36 MiB) Viewed 2731 times
-
- 2830E0F2-EC91-46B3-B8FA-2901948EAD89.jpeg (2.06 MiB) Viewed 2733 times
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
That's more like it!
-
- Minor Maniac
- Posts: 10794
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
I agree.
I would keep as solid plate and only drill the holes necessary to fit the mount bracket to the swivel.
Phil
I would keep as solid plate and only drill the holes necessary to fit the mount bracket to the swivel.
Phil
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Mocked up the new revised calliper hanger, only had 6mm plate and some big washers, had to do some slimming work on the leg. Now it all needs drawing up and need to program the mill and do a test run.
Issues yes, bolt clearances, and flex in the 6mm plate, reality will be a 18mm plate machined down to 13mm for the bridge and 18mm for the calliper .
Issues yes, bolt clearances, and flex in the 6mm plate, reality will be a 18mm plate machined down to 13mm for the bridge and 18mm for the calliper .
- Attachments
-
- D9CD1841-D45F-4394-B1C0-31B9884BA0A1.jpeg (2.62 MiB) Viewed 2688 times
-
- 1CE6EA05-1B29-487B-8082-846978332078.jpeg (2.46 MiB) Viewed 2688 times
-
- CF76AA4D-60A5-47CA-BA07-F055AA3AA59D.jpeg (2.97 MiB) Viewed 2688 times
-
- 9882C74E-7572-4682-B6B3-C8D0B19A99E7.jpeg (3.06 MiB) Viewed 2688 times
-
- 980C80F7-7258-49E4-8905-341EF1A56C12.jpeg (2.73 MiB) Viewed 2688 times
Last edited by fixwheelmad on Tue May 18, 2021 8:19 pm, edited 1 time in total.
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Here you go, hope this makes it all clearer....fixwheelmad wrote: ↑Sun May 16, 2021 8:00 amI’ve got your images, I will take photos of the setup with dimensions, from spindle through to nut ok.Nourish wrote: ↑Sat May 15, 2021 10:15 pm Ah - so when you say shims do you really mean collars? - you're adjusting the diameters and not the lateral position?
Got any dimensions - please?
I posted some drawings on the other side some while ago of the stub axles I made up to fit Vitesse hubs when I was an apprentice - could alter these drawings to do a permanent job.
https://www.morrisminorowners.co.uk/vie ... it=vitesse
- Attachments
-
- 79AA3F15-0766-4875-8A6D-96E2E0DBD582.jpeg (1.84 MiB) Viewed 2688 times
-
- DE425FDE-18E3-4F4B-9220-391A69B8B8CD.jpeg (1.75 MiB) Viewed 2688 times
-
- 14AD00CE-8782-4636-97F7-6188280B2DCF.jpeg (2.29 MiB) Viewed 2688 times
-
- 214E9D92-6775-4598-85E8-5278500358FC.jpeg (2.26 MiB) Viewed 2688 times
-
- 553A35C2-7DB0-4D75-B885-CFF98D8414D3.jpeg (2.82 MiB) Viewed 2688 times
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
Some more images
- Attachments
-
- B52D8EC3-7B0A-4B15-B036-7EC94A3DD4EF.jpeg (3.42 MiB) Viewed 2686 times
-
- 7DE4B32E-E314-48AF-9FB6-ABA9F08FA1EE.jpeg (3.31 MiB) Viewed 2686 times
-
- 85BAA709-86B2-456B-809E-2BA149B581DC.jpeg (2.92 MiB) Viewed 2686 times
-
- 0DD4D6EA-BAEC-4468-B684-2AEC381891B9.jpeg (2.3 MiB) Viewed 2686 times
-
- 00972DF6-7A26-43A4-99A7-5A0EECC1674E.jpeg (2.62 MiB) Viewed 2686 times
-
- Minor Fan
- Posts: 267
- Joined: Tue Jan 16, 2018 2:53 pm
- MMOC Member: No
Re: Newbie, Fiat TC & Volumex HFO 501 NEW BUILD 2018
And closeups...
- Attachments
-
- 5693E759-EF3A-467E-9627-66FD02B63713.jpeg (3.02 MiB) Viewed 2686 times
-
- B77E121C-5B3C-459A-977F-D2FBB4D84641.jpeg (2.96 MiB) Viewed 2686 times
-
- 904E799F-E8A2-4E51-8FE5-FEDF4ED1411A.jpeg (2.56 MiB) Viewed 2686 times
-
- 30424A76-1ED5-4BDC-8D8E-E8127C7786D3.jpeg (2.34 MiB) Viewed 2686 times
-
- 364C9DCB-F8A5-47F6-9310-553302717EEC.jpeg (3.6 MiB) Viewed 2686 times