Traveller Restoration

Let us all know what you are up to with your current restoration project. Get that Minor on the road!
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
Post Reply
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Traveller Restoration

Post by Neil MG »

Well just another restoration thread really!

I am starting to restore a 1965 Traveller. It has only had one owner and was driven up until 1980 and then left in the garage, having failed its MOT. A typical tale no doubt. It seems to have all the usual rust as well as some very '70s repairs - using aluminium and pop rivets in lieu of welded steel!

First job is to strip it down and see just what is left...[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

Other side is not much better[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

And the engine bay...I think some of the newness has worn off here too![frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

I think the first job is to get some strengthening in place so I can tackle the sills and get some structural integrity back...
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
DAVIDMCCULLOUGH
Minor Legend
Posts: 3010
Joined: Sun Sep 09, 2007 10:42 pm
Location: Whiteabbey, Co Antrim
MMOC Member: Yes

Re: Traveller Restoration

Post by DAVIDMCCULLOUGH »

Looks like you got quite a big job to tackle, take your time and dont cut out too much at once and like you say add some strengthening accross the doors and leave the wood in place as long as is possible. I put new floors and sill into my traveller, including the boxing plate and then removed the wood to finish off the area between the the b post and rear inner wing and everything stayed in place ok!!

Good luck and keep on putting up pics :D


Too many Minors so little time.....
irmscher
Minor Legend
Posts: 3773
Joined: Wed Jul 14, 2010 10:53 am
Location: South Manchester
MMOC Member: Yes

Re: Traveller Restoration

Post by irmscher »

That is rusty :( but everything is repairable :D
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

Thanks guys! David that sounds like good advice and is pretty much my plan too.
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
John.n
Minor Friendly
Posts: 86
Joined: Mon Jan 07, 2013 8:01 pm
Location: Derbyshire
MMOC Member: No

Re: Traveller Restoration

Post by John.n »

im in exactly the same boat exept someone has plated the engine bay tie plates aswell any they have rotted away. it comes with a double floor aswell just to help the rust along!
Regards,
John
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

I made a very simple spit so that I can get better access to the floors and you can see the temporary stiffeners I welded in the door apertures.[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

With one of the pop riveted aluminium plates removed...[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
perkinsp3
Minor Friendly
Posts: 27
Joined: Wed Mar 30, 2011 9:45 pm
Location: Leicester
MMOC Member: No

Re: Traveller Restoration

Post by perkinsp3 »

[quote="Neil MG"]I made a very simple spit so that I can get better access to the floors and you can see the temporary stiffeners I welded in the door apertures.

Mines not quite so bad but will need 'turning'
A simple spit sounds useful, any chance of some pics of it?
Thanks
Pete
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

For the spit, I just bolted a couple of bits of old shelf rack to the front and back[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

I just welded a couple of brackets to an old pipe (in fact there were brackets already welded on that worked for the front)[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

The rear had another couple of pieces of rack welded to it to get the right height and then the pole is supported on a couple of A-frames made from the same racking. I already had these but they were too short and so I put some wood underneath.[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

Back to the restoration, I started cutting out the plates that had been welded previously together with the major rot. Starting on the driver's side floor I cut back to good metal, which pretty much matched the repair panel for the floor.[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

On the outside rear of the floor the search for good metal was somewhat fruitless...[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

Same story at the front...[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

So I ended up with a small space...[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
DAVIDMCCULLOUGH
Minor Legend
Posts: 3010
Joined: Sun Sep 09, 2007 10:42 pm
Location: Whiteabbey, Co Antrim
MMOC Member: Yes

Re: Traveller Restoration

Post by DAVIDMCCULLOUGH »

Slow down!!! Yes you want to cut out rotten metal but you do need some reference points to put the new panels in. You can buy a one peice floor section that comes complete with the sill step in place

http://morrisminorspares.co.uk/shop/pro ... e002069cbe

I think this should be your next step to get some strength back in the shell. When I did mine I cut and welded the floor in while the car was still on the ground and then flipped it over to finish all the ill and crossmember welding. I used the complete floor sections as well but at that time they didnt come with the full step fitted just the vertical edge of the step to be welded to the top edge that remained.


Too many Minors so little time.....
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Traveller Restoration

Post by Neil MG »

Thanks David,

Yes, I got that section. I hoped that it might be possible to buy panels to replicate the original design, but as you say that part included the inner sill step, but it is cut and swaged where it meets and the sill is then welded onto the floor section on the wrong side. Also the front flange is formed in the wrong direction on the outer side and continued inboard where there was not one originally. Plus the rear vertical face is formed by bending the floor panel when it should be a separate welded panel. At least there are lots of different repair panels available. I just wish that they were to the original design.

I placed the section in the car to see where to cut it to match the existing good metal. My intention is that everything will be butt welded and ground flush. I have a positive hatred of "patches" so the only overlapping steel will be where panels were originally spot welded together.[frame]Image[/frame]
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Post Reply