Is this the right cylinder
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
Is this the right cylinder
Is this the right cylinders for my rear brakes? My car is a 1956 splitty im scratching my head thinking how i bleed them ? Am I missing something ?
- Attachments
-
- 4CB0D362-41FD-4B32-AD6E-FB435BBB4F98.jpeg (673.4 KiB) Viewed 1408 times
Re: Is this the right cylinder
It looks correct, but be aware that the early cylinders were different from the later ones, so a part number and/or dimensions would be useful. If we can't be 100% certain then buy the correct part from a trusted supplier. If they are the same then a spare is always useful, if they are different then throw that one away, you cannot take a chance on brakes. The bleed screw is behind the backplate, separate from the cylinder; but if you are asking that question then please don't work on the brakes without assistance, they are a safety critical item. The layout of the system is fully explained in all the workshop manuals and most of the parts websites and catalogues are also very clear. You really do need to consult those resources. It should all become clear when you look at the car.
Re: Is this the right cylinder
Ok il dig out the old ones, but that in itself is a big task! I fully agree with you there ,safety first. It was a long time ago I stripped it down, and didn’t really take much notice but it’s all bagged up and labelled.i see there is a banjo connector with copper washers needed. I’m replacing the complete system and il check those resources thank you .simmitc wrote:It looks correct, but be aware that the early cylinders were different from the later ones, so a part number and/or dimensions would be useful. If we can't be 100% certain then buy the correct part from a trusted supplier. If they are the same then a spare is always useful, if they are different then throw that one away, you cannot take a chance on brakes. The bleed screw is behind the backplate, separate from the cylinder; but if you are asking that question then please don't work on the brakes without assistance, they are a safety critical item. The layout of the system is fully explained in all the workshop manuals and most of the parts websites and catalogues are also very clear. You really do need to consult those resources. It should all become clear when you look at the car.
-
- Minor Legend
- Posts: 2775
- Joined: Mon Dec 12, 2011 7:20 pm
- Location: LANCASHIRE (paradise)
- MMOC Member: Yes
Re: Is this the right cylinder
They look similar to the ones on my Morris Oxford MO, which is from 1952. I would compare with what you have already fitted to the car if possible, and if the existing ones are by Lockheed or Girling then save them! A number of firms can revive old brake parts to make them as good as new. You might even be able to re-rubber them if the bores are in good nick. Hope this helps.
Re: Is this the right cylinder
Ok iv found the old unit here’s a pic of them both together
- Attachments
-
- 39A85898-6F81-4047-A4A7-29503D282624.jpeg (3.09 MiB) Viewed 1272 times
-
- Minor Legend
- Posts: 2775
- Joined: Mon Dec 12, 2011 7:20 pm
- Location: LANCASHIRE (paradise)
- MMOC Member: Yes
Re: Is this the right cylinder
Well that looks right, offer it up and see. Here's a tip. Remove the rubber band, allow the piston to pop out and coat it all well with red rubber grease. This will prevent seizure over periods of disuse and make the parts last longer. Also smear some Girling Green grease in the grooves for the sliding backplate, to help the cylinder move freely.
-
- Minor Maniac
- Posts: 10816
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes