Brake system lack of pressure / fluid throughput
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
-
- Minor Legend
- Posts: 1312
- Joined: Thu Jan 28, 2010 4:14 am
- Location: Fulton, Missouri, United States
- MMOC Member: No
Brake system lack of pressure / fluid throughput
Hi all,
My Mog has been laid up since July with failed brakes. The pedal gradually got spongy over the course of a few days, until all pressure was lost.
I checked each wheel (MGB calipers up front, standard cylinders in back) and had no fluid weepage, and the bleed screws were all tight. No fluid drips were evident from the lines, either, so I immediately concluded that it was failed master cylinder seals. I got a new MC on order (shipping to the US is painful on those!). Upon receipt, I disassembled it to remove the "top-hat" seal to work with the discs up front, as you do - I had done the same thing in 2015 with the old MC, with no trouble - reassembled everything in fluid, put it in the car, and -
Nothing! The system would not pressurize and the reservoir level did not drop. With bleed screws open (on the calipers, the type with one-way valves inside so you can just pump and not have to open and close them), no fluid came through, even after a hundred strokes on the pedal. Some very tiny bubbles would come up through the reservoir with each stroke, though.
After some grousing in the MM Facebook groups I came to the conclusion I must have torn a seal in the MC upon reassembly. So, I got a seal kit on order, waited, disassembled and reassembled, put it back in the car, and the same thing happened. No change in symptom whatsoever.
So I'm rather at a loss. Have I torn the new seals again? If so, how do I make that not happen? Or could it be a defective MC (that is, the metal bit)? Or have I missed something somewhere else in the system entirely?
Any input appreciated...
My Mog has been laid up since July with failed brakes. The pedal gradually got spongy over the course of a few days, until all pressure was lost.
I checked each wheel (MGB calipers up front, standard cylinders in back) and had no fluid weepage, and the bleed screws were all tight. No fluid drips were evident from the lines, either, so I immediately concluded that it was failed master cylinder seals. I got a new MC on order (shipping to the US is painful on those!). Upon receipt, I disassembled it to remove the "top-hat" seal to work with the discs up front, as you do - I had done the same thing in 2015 with the old MC, with no trouble - reassembled everything in fluid, put it in the car, and -
Nothing! The system would not pressurize and the reservoir level did not drop. With bleed screws open (on the calipers, the type with one-way valves inside so you can just pump and not have to open and close them), no fluid came through, even after a hundred strokes on the pedal. Some very tiny bubbles would come up through the reservoir with each stroke, though.
After some grousing in the MM Facebook groups I came to the conclusion I must have torn a seal in the MC upon reassembly. So, I got a seal kit on order, waited, disassembled and reassembled, put it back in the car, and the same thing happened. No change in symptom whatsoever.
So I'm rather at a loss. Have I torn the new seals again? If so, how do I make that not happen? Or could it be a defective MC (that is, the metal bit)? Or have I missed something somewhere else in the system entirely?
Any input appreciated...
The way to a man's heart may be making food, but the way to my heart is buying me car parts!
Come read about my Minor at An American Moggie.
Come read about my Minor at An American Moggie.
-
- Minor Fan
- Posts: 120
- Joined: Wed Feb 06, 2008 5:01 pm
- Location: Phoenix, Arizona. Valley of the sun.
- MMOC Member: No
Re: Brake system lack of pressure / fluid throughput
I don't think you have a problem ... once you get fluid moving you will be able to bleed normally, I believe we need the weight of a line full of fluid to get things going and you need to get fluid into the lines, I use a vacuum pump now, seems to work especially well on the minor which has always been problematic with brake system maintenance, previous to that I used to use my hand on the foot peddle and pump like a maniac until the master started pumping !! Good luck.
-
- Minor Legend
- Posts: 2646
- Joined: Thu May 11, 2006 10:34 am
- Location: Cardiff
- MMOC Member: Yes
Re: Brake system lack of pressure / fluid throughput
Have you tried pinching off the hoses to the front cylinders to halve the quantity of fluid you need to move? Once the back is done, push the pistons deep into the calipers to reduce the air. Sounds like you might have so much air in there that the fluid is sort of just bouncing back as you release the pedal.
Might work?
Might work?
Cardiff, UK
-
- Minor Legend
- Posts: 1312
- Joined: Thu Jan 28, 2010 4:14 am
- Location: Fulton, Missouri, United States
- MMOC Member: No
Re: Brake system lack of pressure / fluid throughput
An air lock is something I've considered, but I discounted the possibility because fluid doesn't move even when the bleed screws are open (air can't lock when the system freely vents, right...?). But I'll get a vacuum pump and try it out - if it fails, that's just another datum point!
The way to a man's heart may be making food, but the way to my heart is buying me car parts!
Come read about my Minor at An American Moggie.
Come read about my Minor at An American Moggie.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Brake system lack of pressure / fluid throughput
Try jacking the rear of the Minor as high as you can.
I once had to deal with a Minor with similar problems that needed the car to be nearly stood on its nose to get the air out of the system.
I once had to deal with a Minor with similar problems that needed the car to be nearly stood on its nose to get the air out of the system.
-
- Minor Legend
- Posts: 1053
- Joined: Tue Nov 08, 2016 3:18 pm
- Location: Manchester ( Damp and Miserable ) and that's just the wife...
- MMOC Member: Yes
Re: Brake system lack of pressure / fluid throughput
Let us know how the vacuum pump works,it's on my "to do" list...Fingolfin wrote: ↑Wed Oct 17, 2018 11:01 pm An air lock is something I've considered, but I discounted the possibility because fluid doesn't move even when the bleed screws are open (air can't lock when the system freely vents, right...?). But I'll get a vacuum pump and try it out - if it fails, that's just another datum point!
John
-
- Minor Addict
- Posts: 656
- Joined: Fri Apr 18, 2014 2:40 pm
- Location: Vogelsberg - Germany
- MMOC Member: No
Re: Brake system lack of pressure / fluid throughput
Have had similar problems and I came to the conclusion, rightly or wrongly that the rear brakes were the problem with air not being expelled. Normally I bleed the brakes myself but to solve the problem I had a friend do the pedal pumping for me with the rear of the car, like Phil said raised as high as possible. Thence he pushed the pedal down as quickly as possible several times with a pause in between and indeed ( only the rear brakes ) some small air bubbles could be seen in the tube.philthehill wrote: ↑Thu Oct 18, 2018 7:04 am Try jacking the rear of the Minor as high as you can.
I once had to deal with a Minor with similar problems that needed the car to be nearly stood on its nose to get the air out of the system.
Much better now but it was a long odyssy to get there
Gott schütze mich vorm Sturm und Wind und Autos, die aus England sind.
download/file.php?id=4822[/sig]
download/file.php?id=4822[/sig]
-
- Minor Legend
- Posts: 1438
- Joined: Tue Jan 30, 2007 10:09 pm
- Location: Essex
- MMOC Member: No
Re: Brake system lack of pressure / fluid throughput
I made an adapter to screw in the top of the MC which allows a few psi to be applied to the system, then open bleed screws and allow the positive pressure to push fluid/air through.
Don't let fluid get too low!
To me it sounds like you have a big wodge of air which is compressing rather than moving.
Alan
Don't let fluid get too low!
To me it sounds like you have a big wodge of air which is compressing rather than moving.
Alan
-
- Minor Legend
- Posts: 1312
- Joined: Thu Jan 28, 2010 4:14 am
- Location: Fulton, Missouri, United States
- MMOC Member: No
Re: Brake system lack of pressure / fluid throughput
Last night I only had time enough to try the vacuum pump on one of the front bleed screws. Upon pumping up, I got a few drops of fluid out, but never a consistent flow. My thought now is that there may be a blockage in the line going to the front brakes.
Will try rears this evening...
Will try rears this evening...
The way to a man's heart may be making food, but the way to my heart is buying me car parts!
Come read about my Minor at An American Moggie.
Come read about my Minor at An American Moggie.
-
- Minor Legend
- Posts: 1186
- Joined: Mon Apr 23, 2007 2:32 pm
- Location: Dartmoor
- MMOC Member: No
Re: Brake system lack of pressure / fluid throughput
Check if the flexis have collapsed internally - i had this problem a couple of months ago whereby I couldn't bleed the fronts after changing the cylinders (on mmy Wolseley Six, but same principle) and it was due to a collapsed flexi that wasn't allowing fluid through on the side that I was trying to bleed first. Hose replaced and all was well.
-
- Minor Addict
- Posts: 769
- Joined: Sat Oct 31, 2009 8:51 pm
- Location: Epsom, Surrey
- MMOC Member: No
Re: Brake system lack of pressure / fluid throughput
i would crack a brake union at the highest point in the brake system as well. Slacken it on the brake pipe junction. push the pedal. i'd also check one of the front brake pipes hasn't collapsed internally.
-
- Minor Addict
- Posts: 630
- Joined: Mon Feb 03, 2014 5:16 pm
- Location: Gt Holland, Essex
- MMOC Member: Yes
Re: Brake system lack of pressure / fluid throughput
For bleeding vacuum bleeder all the way, works an absolute treat with no messing. Really easy, whole car can be bled in half an hour, single handed with a perfect pedal.
-
- Minor Legend
- Posts: 1053
- Joined: Tue Nov 08, 2016 3:18 pm
- Location: Manchester ( Damp and Miserable ) and that's just the wife...
- MMOC Member: Yes
Re: Brake system lack of pressure / fluid throughput
As soon as I can get round to building the Vacuum bleed kit I'll give it a go....
John
John
-
- Minor Legend
- Posts: 1312
- Joined: Thu Jan 28, 2010 4:14 am
- Location: Fulton, Missouri, United States
- MMOC Member: No
Re: Brake system lack of pressure / fluid throughput
Thanks to everyone who gave me suggestions on this thread. It took four different bleeding sessions, but it did in fact turn out to be an air lock - the pedal is now quite firm and the car stops nicely.
There probably was no need to replace the seals in the MC...but it has been a learning experience, so I should try to be satisfied with that.
There probably was no need to replace the seals in the MC...but it has been a learning experience, so I should try to be satisfied with that.
The way to a man's heart may be making food, but the way to my heart is buying me car parts!
Come read about my Minor at An American Moggie.
Come read about my Minor at An American Moggie.