rear crankshaft scroll.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: rear crankshaft scroll.
Whilst this is a light hearted photo and I did not swing the Beast of Turin it is important to note the position of my thumb on the starter handle.
- Attachments
-
- Beast14.JPG (1.52 MiB) Viewed 1237 times
-
- Minor Friendly
- Posts: 55
- Joined: Fri Jan 17, 2014 4:39 pm
- MMOC Member: Yes
Re: rear crankshaft scroll.
Very wise. I'll bear this in mind.
-
- Minor Friendly
- Posts: 55
- Joined: Fri Jan 17, 2014 4:39 pm
- MMOC Member: Yes
Re: rear crankshaft scroll.
Update on the oil leak from rear of engine. While ordering the starter pull cable, I ordered a non vented cap. Cable fitted and new oil cap fitted I drove round the block a few times to get it warmed up. Parking it on the drive, I immediately went for the sand bucket to catch the drips. Lo and behold --3 drops of oil from the jiggle pin and that was it I can live with that.. I'll go a longer drive tomorrow but for today, things are a bit more hopeful.
Thanks again guys for all your input.
Thanks again guys for all your input.
-
- Minor Friendly
- Posts: 55
- Joined: Fri Jan 17, 2014 4:39 pm
- MMOC Member: Yes
Re: rear crankshaft scroll.
Having been waylaid on the gardening front, I am back on trying to remove the top cove off my "spare" engine. The heads of the three bolts are jamming against the crankshaft flange (see photo). I removed the backplate to see if that would help. The top cover is now loose but I cant remove it as I can't get the bolts out. apart from cutting the bolts, does anybody have any tips on this?philthehill wrote: ↑Sat Apr 06, 2019 8:53 am The scroll will still be on the crankshaft.
You may have to rob a rear cover off an unserviceable block. It may be worth doing a search on 'e' bay - or you could borrow the top cover off your spare engine.
- Attachments
-
- 20190418_cover.jpg (4.44 MiB) Viewed 1116 times
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: rear crankshaft scroll.
Try removing the plate with the bolts still in the holes. The plate does not have a flange, it just fits flat against the rear face of the block so it will just slide upwards once you have broken the gasket seal.
I have just removed one of the three bolts (after breaking the lock wire) securing the plate on a spare small block 'A' Series and it could be removed without any difficulty.
The three bolts should have a pair of holes through the bolt head to allow for the fitting of the lock wire.
If your bolts do not have the holes then you appear to have the incorrect bolts fitted which may be longer than original.
If you cannot remove the plate with the bolts through the holes please come back on here for further advice.
The length of bolt under the head is 9/16". Diameter 1/4" UNF with 7/16" Across the flats (A/F) head.
The bolts should be secured in place with locking wire and not have spring washers as you appear to have fitted.
I have just removed one of the three bolts (after breaking the lock wire) securing the plate on a spare small block 'A' Series and it could be removed without any difficulty.
The three bolts should have a pair of holes through the bolt head to allow for the fitting of the lock wire.
If your bolts do not have the holes then you appear to have the incorrect bolts fitted which may be longer than original.
If you cannot remove the plate with the bolts through the holes please come back on here for further advice.
The length of bolt under the head is 9/16". Diameter 1/4" UNF with 7/16" Across the flats (A/F) head.
The bolts should be secured in place with locking wire and not have spring washers as you appear to have fitted.
-
- Minor Friendly
- Posts: 55
- Joined: Fri Jan 17, 2014 4:39 pm
- MMOC Member: Yes
Re: rear crankshaft scroll.
Hi philthehil. Thanks for the quick reply. There are no holes in the bolt heads for tying wire. Thebolts are 7/16AF and 1/4 diameter.
The bolts are unscrewed as far as possible but still "feel"as though they are still screwed into the block. the top cover is loose but but can't remove it due to the bolts.
The bolts are unscrewed as far as possible but still "feel"as though they are still screwed into the block. the top cover is loose but but can't remove it due to the bolts.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: rear crankshaft scroll.
I am afraid you have three courses of action and they are:-
1, Cut the heads off the bolts so as they can be unscrewed further to allow the top cover to slide upwards and off the block.
2. Remove the crankshaft.
3. Obtain a top cover and the three correct locking wire bolts off another engine. I would suggest that you put a request for a top cover and bolts on here in the wanted section.
1, Cut the heads off the bolts so as they can be unscrewed further to allow the top cover to slide upwards and off the block.
2. Remove the crankshaft.
3. Obtain a top cover and the three correct locking wire bolts off another engine. I would suggest that you put a request for a top cover and bolts on here in the wanted section.
-
- Minor Friendly
- Posts: 55
- Joined: Fri Jan 17, 2014 4:39 pm
- MMOC Member: Yes
Re: rear crankshaft scroll.
Add now in the wanted section
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: rear crankshaft scroll.
The wanted request is not appearing in the wanted section. You may have to submit again.
-
- Minor Friendly
- Posts: 55
- Joined: Fri Jan 17, 2014 4:39 pm
- MMOC Member: Yes
Re: rear crankshaft scroll.
Thought I had posted it right away. Anyway, it is there now. Sadly plenty of views but none for sale yet.