12G940 Cylinder Head

Discuss mechanical problems here.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
Post Reply
Martlin
Minor Friendly
Posts: 48
Joined: Wed May 08, 2019 4:32 pm
MMOC Member: Yes

12G940 Cylinder Head

Post by Martlin »

Hi all,
Just purchased a reconditioned 12G940 cylinder head,all good so far.
I am an elderly,and often quite confused!
Looking at the head not only is there no provision for a bypass stub,also the heater outlet where the tap goes is blocked off!
I have had good advice how to overcome the missing stub pipe,but cannot understand why the heater outlet is blocked off.
O.K,what do you think, if I drill out the heater outlet I might as well drill and tap the bypass stub connection.
What do you think.
Thanks for bearing with me.
Martin.
E03D3FB4-65E0-456B-B640-E2C116705949.jpeg
E03D3FB4-65E0-456B-B640-E2C116705949.jpeg (2.39 MiB) Viewed 1888 times
24204B01-4875-4C1A-9B8C-9E2E5E20CB61.jpeg
24204B01-4875-4C1A-9B8C-9E2E5E20CB61.jpeg (2.94 MiB) Viewed 1888 times
BA6B2F10-599C-4623-BE7A-552665BEFC3B.jpeg
BA6B2F10-599C-4623-BE7A-552665BEFC3B.jpeg (2.82 MiB) Viewed 1888 times
7AF17534-2596-4F06-AD2F-1BCF5D83ABF4.jpeg
7AF17534-2596-4F06-AD2F-1BCF5D83ABF4.jpeg (2.87 MiB) Viewed 1888 times
7AF17534-2596-4F06-AD2F-1BCF5D83ABF4.jpeg
7AF17534-2596-4F06-AD2F-1BCF5D83ABF4.jpeg (2.87 MiB) Viewed 1888 times
les
Minor Maniac
Posts: 8737
Joined: Tue Feb 12, 2002 12:00 am
Location: kent
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by les »

The heater outlet looks like it’s full of something, are you sure you can’t dig the blockage out?

Banned User
Minor Fan
Posts: 319
Joined: Tue Jan 29, 2019 9:37 am
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by Banned User »

les wrote: Thu Sep 12, 2019 5:23 pm The heater outlet looks like it’s full of something, are you sure you can’t dig the blockage out?
It's an A+ head, that's how they were.
les
Minor Maniac
Posts: 8737
Joined: Tue Feb 12, 2002 12:00 am
Location: kent
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by les »

Ah, didn’t know that.

paul 300358
Minor Fan
Posts: 467
Joined: Thu May 11, 2017 8:23 pm
Location: South Cheshire
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by paul 300358 »

Martin, don't worry, drill the heater outlet out, the holes are there and threaded for the heater valve studs. Don't bother drilling and tapping the bypass.

Regards
Paul
Martlin
Minor Friendly
Posts: 48
Joined: Wed May 08, 2019 4:32 pm
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by Martlin »

Hi,
Thanks for help so far,
In reply to Les I was hoping it was crud,but is solid steel!
IslipMinor
Minor Legend
Posts: 2147
Joined: Mon May 10, 2004 9:10 pm
Location: Oxford, UK
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by IslipMinor »

The A-Plus engines used a different by-pass system that had a sandwich plate underneath the thermostat housing. This also provides the permanent feed of hot water to the heater.

Despite frequent suggestions to ignore the original by-pass hose and just block it off, no production A-Series engines were ever made with no by-pass. On standard 948 and 1098 engines history appears to suggest that you can get away with drilling a hole in the thermostat, but does that provide a by-pass or just a bleed for air bubbles? What is the history for 1275 engines?

On our well modified 1380, the heater outlet has always been permanently connected, but following the apparent success on this Board of rapid heater warm-up etc., running with no by-pass was a complete well-documented disaster. Without the circulation around the front of the engine we had multiple problems with No. 1 valve sticking and burning out.

Since putting the original non-A-Plus by-pass back, we have had no valve problems for many years and 10's of thousands of miles. The by-pass system in car cooling systems (not just the A-Series) is there for a reason! It is even more important with unleaded fuel that causes the exhaust valve to run hotter, thus the need for hardened seats and improved valve material.
Richard


Banned User
Minor Fan
Posts: 319
Joined: Tue Jan 29, 2019 9:37 am
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by Banned User »

How about one of these to avoid heating the cabin in the summer? https://www.t7design.co.uk/tx2-heater-valve.html
philthehill
Minor Maniac
Posts: 10766
Joined: Thu Jul 19, 2012 12:05 pm
Location: Hampshire
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by philthehill »

Not only do you need good coolant flow around the front of the head but also around the rear of the head so as to reduce the possibility of hot spots. The rear of the head is prone to having higher temperatures due to its design.
A large capacity water pump helps to push additional water around the heal so helping to reduce the chance of hot spots.
As regards the by-pass facility I have mixed views having run both with and without the bypass facility. My 1275cc blocked engines up to 1400cc have all run without the bypass facility but they have always been fitted with large capacity water pumps and bronze valve guides with good clearance between valve stem and guide. The current head fitted to my Minor has had additional water transfer holes made to help eliminate hot spots.
No two engines are the same and whilst one engine may run perfectly satisfactory another of the same spec may not.

Good coolant circulation is the secret.

Phil

paul 300358
Minor Fan
Posts: 467
Joined: Thu May 11, 2017 8:23 pm
Location: South Cheshire
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by paul 300358 »

If you look at the cooling page on the Carver website ( https://www.calverst.com/technical-info ... -it-works/ ) it says

"Back to thermostats for a moment. It is common practice to remove this and fit a blanking sleeve in a bid to improve cooling. If this is done, you must blank off the by-pass hose, otherwise stagnant areas of water will occur causing the dreaded hot-spots. However, the danger with fitting a blanking sleeve is that the engine may not reach proper operating temperatures, and this can be every bit as bad as running a little too hot. And the old style blanking sleeve (11G176) is not at all efficient. I would strongly advise using a thermostat in ALL road cars, of at least 82 degrees to make sure the correct running temperatures are achieved. A blanking sleeve is not the answer to over-heating problems. I always run a thermostat in my race engines unless bound for foreign shores where high ambient temperatures are experienced. Many folk think that they have to fit a blanking sleeve if they are blanking off the by-pass hose. Not so. Blank off the troublesome by-pass hose then fit a thermostat that has had six or eight eighth-inch holes drilled around the periphery. These holes allow coolant to circulate before the engine is up to temperature and the thermostat opens."

I found that one hole was adequate for a near standard 1098, any more and it was over cooled.
IslipMinor
Minor Legend
Posts: 2147
Joined: Mon May 10, 2004 9:10 pm
Location: Oxford, UK
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by IslipMinor »

Paul,

The significance of the Calver article is the combination of no by-pass AND the blanking sleeve. With no thermostat fitted there is plenty of water circulation at all times. The whole purpose of the 'blanking sleeve' is to create a good flow around the engine, without a thermostat in place. No thermostat and no blanking sleeve leads to very quick local overheating. The description 'blanking sleeve' is very misleading, it doesn't 'blank' anything, it directs the flow around the engine, that otherwise would take a shortcut and overheat the engine very quickly.

The role of the the by-pass circuit is to provide water circulation around the engine UNTIL the thermostat opens, which then provides circulation around both the engine and the radiator.

Minors are well-known for having a good capacity cooling system, which is why, at least in part, it is possible to 'get away' with blocking off the by-pass system on a standard engine. Firsthand experience says don't try it on a modified 1275, which needs a lot more cooling capacity than either of the standard Minor A-Series engines.

My well-documented concern is the often quoted statement that the by-pass hose was removed on the A-Plus engines, so why not do the same on the Pre-A-Plus engines? Yes, it was removed, and it was replaced by an even bigger capacity by-pass system using the sandwich plate.
Richard


philthehill
Minor Maniac
Posts: 10766
Joined: Thu Jul 19, 2012 12:05 pm
Location: Hampshire
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by philthehill »

A thermostat or 'Blanking Plate' sic cannot be fitted directly to the cylinder head in question as the hole is not machined for either
To fit either a thermostat or blanking plate the sandwich plate is required.
100_1420.JPG
100_1420.JPG (1.6 MiB) Viewed 1788 times
If you fit the sandwich plate it throws out of alignment the thermostat housing and the radiator inlet and different hoses have to used to join the two together.

IslipMinor
Minor Legend
Posts: 2147
Joined: Mon May 10, 2004 9:10 pm
Location: Oxford, UK
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by IslipMinor »

Phil,

The head has the recess for the thermostat - why could it not be fitted directly to the head in the picture?
Richard


philthehill
Minor Maniac
Posts: 10766
Joined: Thu Jul 19, 2012 12:05 pm
Location: Hampshire
MMOC Member: Yes

Re: 12G940 Cylinder Head

Post by philthehill »

Richard
Looking at the picture again - you are right.

It should be born in mind though that not all 940 'A' plus heads will accept the direct fitting of the thermostat. My own 940 'A' Plus head has no facility to fit a thermostat and the sandwich plate has to be used if a thermostat is required to be fitted.

The casting underneath the heater outlet stub had to drilled through to allow the passage of coolant to the heater.
Phil

Post Reply