Pick up Restoration (Part 1)

Let us all know what you are up to with your current restoration project. Get that Minor on the road!
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

There had been a blue cover on her at one time, seemed a shame to leave her uncovered, so we put it back so she can rust in peace.

<br>Image<br>
Last edited by davidmiles on Wed Feb 10, 2010 9:25 pm, edited 2 times in total.
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
ssnjimb
Minor Fan
Posts: 425
Joined: Fri Nov 28, 2008 2:41 pm
Location: Worcestershire
MMOC Member: No

Post by ssnjimb »

I wish someone would please reserect her.

All minors deserve reserecting.

One day someone will make that decision on our minors when we are sadly not around anymore (Brings a tear to my eye)

James
I own a 1974 MG Midget 1275 in Teal Blue "Midget" is what we call him and he is in very good to excellant condition "midget" is a Chrome bumper/Round Wheel arch model.
aupickup
Minor Maniac
Posts: 6004
Joined: Tue Jul 20, 2004 11:41 pm
Location: lanark
MMOC Member: No

Post by aupickup »

let it rust in peace
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

Today started with the removal of the support panel, to be kept for later repair..<br>Image<br>
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

this patch was cut and shaped to fit the profile of the inner curve of the wheel arch.<br>Image<br>
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

the location meant it was hard to fit a clamp, so I used electrical tape to hold it while I tacked it into place from the top side.<br>Image<br>
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

the tacking from the top left the original hole locations ready for drilling to make accurate fitting of the bump stop panel.<br>Image<br>
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

One thing that came to light today that worried me, this rust here, the wire wheel cleared away some rust to expose this little horror..<br>Image<br>
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

The hole through the wheel arch that is opposite the damper, does this mean reduced support for the suspension, I guess I've got to get that damper off and see whats behind it, anyone know how that comes off?<br>Image<br>
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
bigginger
Minor Maniac
Posts: 5928
Joined: Thu Sep 09, 2004 11:01 pm
MMOC Member: No

Post by bigginger »

Undo the 4 bolts passing through it that you can see, after bending back the lock tabs. 1/4" W, IIRC
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

Cheers Andrew, thats next on the cards then.
<br>Image<br>
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
aupickup
Minor Maniac
Posts: 6004
Joined: Tue Jul 20, 2004 11:41 pm
Location: lanark
MMOC Member: No

Post by aupickup »

hmm thats looks a bit more involved, and it is the main structural point for the front suspension of course

soak the bolts in plus gas or apply heat to get them out, you do not want the captive nuts behind being wrecked
bigginger
Minor Maniac
Posts: 5928
Joined: Thu Sep 09, 2004 11:01 pm
MMOC Member: No

Post by bigginger »

Threaded plates, FWIW, but it's a GOOD point
aupickup
Minor Maniac
Posts: 6004
Joined: Tue Jul 20, 2004 11:41 pm
Location: lanark
MMOC Member: No

Post by aupickup »

yes sorry threaded plates quite right :D :D
rayofleamington
Moderator
Moderator
Posts: 7679
Joined: Fri Nov 01, 2002 2:55 pm
Location: LEAMINGTON SPA
MMOC Member: No

Post by rayofleamington »

the location meant it was hard to fit a clamp, so I used electrical tape to hold it while I tacked it into place from the top side.
my favourite tool for that job is a hammer handle (wooden - and charred if it's mine).
If you have a hand held mask it means you have no hand left to hold it (although that never bothered me for 18 years) it is far easier when you have a fully auto head mask as you then have a free hand for things like that.
Electrical tape, a big magnet and many other things can be useful to hold a patch - including the jack if you're under the car.
Ray. MMOC#47368. Forum moderator.

Jan 06: The Minor SII Africa adventure: http://www.minor-detour.com
Oct 06: back from Dresden with my Trabant 601 Kombi
Jan 07: back from a month thru North Africa (via Timbuktu) in a S3 Landy
June 07 - back from Zwickau Trabi Treffen
Aug 07 & Aug 08 - back from the Lands End to Orkney in 71 pickup
Sept 2010 - finally gave up breaking down in a SII Landy...
where to break down next?
2013... managed to seize my 1275 just by driving it round the block :(
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

Thanks Ray, I couldn't hold it from the other side, but I did enlist the help of a length of jammed up timber to put pressure on the plate, it needed to be held hard up against the wheelarch to make a good contact. And yes, just like your hammer handle, it was a little charred.
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

Dennis and Andrew, I dashed out to check the bolt I had drawn out from the damper was full length, I remember it went kind of sudden, it sheared off the tip of the bolt, the tip is now stuck in this captive plate you mention, not seen it yet, tommorow. how I'm going to get that tip out? I don't know yet.
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
bigginger
Minor Maniac
Posts: 5928
Joined: Thu Sep 09, 2004 11:01 pm
MMOC Member: No

Post by bigginger »

Oh damn.I've never had any luck with that problem, I'm afraid. I've tried the easy outs in the past, but without luck. I meant to say earlier that you should be V careful using heat on them, as the bolts are long and the heat will be heating up the oil in the damper. The plate is sort of get at-able through the flitch if you cut a hole, but not really enough to be useful, except spray/dribble on penetrating oil - which could be worth a shot before trying the other bolts. I can't really advise on the almost inevitable replacement of the plate though - somebody here must have managed it. I couldn't see a way without cutting out the front of the bulkhead X member, but didn't/don't trust my welding skills enough to do the repair/replacement. All I can advise is waiting for a pro (IE JLH, surprise) who will probably have more helpful things to say.
jaekl
Minor Addict
Posts: 611
Joined: Thu Jun 19, 2008 7:40 pm
Location: Pennsylvania, USA
MMOC Member: No

Post by jaekl »

Mid way through Series III they added fresh air vent. The inlet are holes in the back side of the crossmember where the shocks are mounted. I assume the Series V cars still have these holes. Once you can flip the cab over, you will be able to spray your penetrating oil onto the ends of the bolts or apply heat if you must. I believe the outboard bolts are easier to get to than the inner ones. I got a nut on the end of one of the bolts through this hole. The previous owner drilled out the bolt and oversized the hole.
davidmiles
Minor Legend
Posts: 2731
Joined: Mon Mar 23, 2009 4:54 pm
Location: Sussex
MMOC Member: No

Post by davidmiles »

The bolts are putting up one hell of a fight, "what the hell have I started here".
number 1 sheared of its tip in the plate, number two has frozen and threatens to shear off, three kind of jumps in a series of bangs. and number four, well I can't get at it yet...<br>Image<br>
Last edited by davidmiles on Tue Jun 02, 2009 9:51 pm, edited 2 times in total.
smile, you never know, you might be winning.[IMG]http://i67.tinypic.com/2ro3j37.jpg[/IMG]
Post Reply