Need an excuse to buy a lathe

Discuss mechanical problems here.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
Post Reply
culp
Minor Fan
Posts: 186
Joined: Mon Feb 08, 2010 6:55 pm
MMOC Member: Yes

Need an excuse to buy a lathe

Post by culp »

Hello,

I want to get a lathe. I'm mildly obsessed with the things and am keen to learn as much as I can. All I can think of that I might use it for with my traveller is to machine a drift for replacing valve guides. What other uses are there for a lathe when it comes to working on classic cars?
bmcecosse
Minor Maniac
Posts: 46561
Joined: Wed Feb 16, 2005 11:24 pm
Location: ML9
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by bmcecosse »

Make a set of pistons? Lighten the flywheel? Skim brake drums ? Machine away excessive length on camshaft sprockets when the cam endfloat is excessive :)
ImageImage
Image
Trickydicky
Minor Legend
Posts: 1565
Joined: Fri Aug 05, 2011 9:53 pm
Location: Leeds, West Yorkshire
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by Trickydicky »

Rear seal plugs for front and rear damper refurbisment :D
After spending 20+ years as a centre lathe turner I have lost count of the amount of "guvvy" jobs I have done for people in my lunch hour.
I think the best one I did was to machine a bearing housing and shaft for a model gyrocopter my father was building. The bearing housing was made from plastic with a silver steel shaft. :D
Wish I had room for one in the garage :(
Richard

Opinions are like people,everyone can be different.
philthehill
Minor Maniac
Posts: 10767
Joined: Thu Jul 19, 2012 12:05 pm
Location: Hampshire
MMOC Member: Yes

Re: Need an excuse to buy a lathe

Post by philthehill »

Once you have a lathe you can do and manufacture all sorts of things (including camshaft sprockets ha, ha :D and still no feedback from Mowog). You will wonder how you ever managed without one.
If you want to do a Minor flywheel you will need a lathe with a min of 11" swing.
If you do buy a lathe you do not have to buy a expensive modern one to do the business.
There are lots of good old ones on 'e' bay or even private sales and so long as you do not mind exposed gearing and possible flat belting you can pick up a good one for £200 - £300 or even less.
The basics principles of the old and new lathes are the same.
The old ones usually come with lots of extras which have been built up and added to over many years.
My latest lathe purchase is over 100 years old, came with an interesting history (500cc motorcycle and F3 racing), has an 16" swing (really useful) and lots of extras, is in excellent condition (no bed or headstock bearing wear) having had little hard use so is still accurate; and having been in preservation for many years and was owned by a retired engineer for over 60 years and was under £200.
A good place to find and learn out about lathes is http://www.lathes.co.uk/page3.html
Best of luck in your search.

bmcecosse
Minor Maniac
Posts: 46561
Joined: Wed Feb 16, 2005 11:24 pm
Location: ML9
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by bmcecosse »

If it comes with a faceplate (and sufficient swing - some come with a removable slide section) - you can skim cylinder heads too! :)
ImageImage
Image
biomed32uk
Minor Addict
Posts: 630
Joined: Mon Feb 03, 2014 5:16 pm
Location: Gt Holland, Essex
MMOC Member: Yes

Re: Need an excuse to buy a lathe

Post by biomed32uk »

I will second and third that, there are a million and one uses for a lathe, and you will wonder how you did without one.

I have a 1954 Boxford, which is a very popular lathe and is very good for the home workshop, being fairly compact, you wont get a flywheel in it but none the less a very useful tool, I was lucky enough to be given it on one of the "it has to disappear over the weekend" schemes, which it did :D .

I also have a Tom Senior M1 mill in the workshop, that's the next most useful versatile machine I have.
bmcecosse
Minor Maniac
Posts: 46561
Joined: Wed Feb 16, 2005 11:24 pm
Location: ML9
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by bmcecosse »

Lucky you!
ImageImage
Image
culp
Minor Fan
Posts: 186
Joined: Mon Feb 08, 2010 6:55 pm
MMOC Member: Yes

Re: Need an excuse to buy a lathe

Post by culp »

So basically making parts from scratch?
bmcecosse
Minor Maniac
Posts: 46561
Joined: Wed Feb 16, 2005 11:24 pm
Location: ML9
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by bmcecosse »

A crankshaft could be a bit of a challenge....
ImageImage
Image
les
Minor Maniac
Posts: 8737
Joined: Tue Feb 12, 2002 12:00 am
Location: kent
MMOC Member: Yes

Re: Need an excuse to buy a lathe

Post by les »

Will you get the use from it? I had a super 7 for over 10 years and used it once. I then bought an ML10 and never used it, it was 3 phase and needed converting, eventually sold that as well! If you've not got many jobs in mind, weigh up the cost of the lathe against the price of getting the odd job done elsewhere. I'm quids in! :D

culp
Minor Fan
Posts: 186
Joined: Mon Feb 08, 2010 6:55 pm
MMOC Member: Yes

Re: Need an excuse to buy a lathe

Post by culp »

Thanks to everyone for the help
alexmcguffie
Minor Fan
Posts: 472
Joined: Mon Nov 18, 2013 11:07 am
Location: Oxfordshire
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by alexmcguffie »

Les has a point. If I didn't have access to a good lathe then I would either buy new bits or buy a few pints for a friend who has a lathe. Both of which a cheaper in the longrun than the outlay for a good lathe. Being able to use a lathe/mill well is a good skill to have but weigh up the usage angainst cost first.
Glad to be back!
culp
Minor Fan
Posts: 186
Joined: Mon Feb 08, 2010 6:55 pm
MMOC Member: Yes

Re: Need an excuse to buy a lathe

Post by culp »

Ah but now you're talking logic and rationalism...basically I want to get a lathe for no better reason than....I want to get a lathe :D so I'm trying to justify it to myself by thinking "just look at all those jobs it'll be good for" Not much rationalism here I'm afraid :roll:
Tudge
Minor Fan
Posts: 104
Joined: Thu Jun 06, 2013 10:08 pm
Location: Herefordshire, West Midlands
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by Tudge »

You can use it to make a replacement eyebolt to give negative camber:

https://www.youtube.com/watch?v=GHvjjFawfj0
1965 2Dr - She's called Lola

bmcecosse
Minor Maniac
Posts: 46561
Joined: Wed Feb 16, 2005 11:24 pm
Location: ML9
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by bmcecosse »

Oh yes - I had forgotten that one. In fact you could make LOTS of them - and sell them to the rest of us! :D
ImageImage
Image
MarkyB
Minor Maniac
Posts: 7845
Joined: Thu Jan 25, 2007 3:18 pm
Location: South East London
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by MarkyB »

All very old school, why not get a nice computer controlled one?
http://www.ebay.co.uk/itm/Colchester-CN ... 2c8a9c8499

"Once you break something you will see how it was put together"
bmcecosse
Minor Maniac
Posts: 46561
Joined: Wed Feb 16, 2005 11:24 pm
Location: ML9
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by bmcecosse »

Where's the fun in that....? :wink:
ImageImage
Image
alexmcguffie
Minor Fan
Posts: 472
Joined: Mon Nov 18, 2013 11:07 am
Location: Oxfordshire
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by alexmcguffie »

That's quite good value :)
Glad to be back!
philthehill
Minor Maniac
Posts: 10767
Joined: Thu Jul 19, 2012 12:05 pm
Location: Hampshire
MMOC Member: Yes

Re: Need an excuse to buy a lathe

Post by philthehill »

I think that this lathe or similar would serve your needs just as well and will do all the turning that you would require for a Minor and if you decide that you do not need a lathe you can always sell it on without loosing lots of money.
http://www.lathes.co.uk/advertphoto/140502eta/
It has a gap bed, has the chucks you require and a faceplate. It has adjustable headstock bearings, a must and it looks all ready to go; and the price is not extortionate at £275.

bmcecosse
Minor Maniac
Posts: 46561
Joined: Wed Feb 16, 2005 11:24 pm
Location: ML9
MMOC Member: No

Re: Need an excuse to buy a lathe

Post by bmcecosse »

If only I had somewhere to put a lathe like that.... :cry:
ImageImage
Image
Post Reply