Hi,
Please could I have some help with regard to the correct type of ignition items that would have originally been fitted to a 1950 sidevalve.
What type of dizzy cap, leads and plug connectors is what I would like to know.
Thank you.
Pete.
Ignition bits, original fittings. Advice needed.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
-
- Minor Friendly
- Posts: 52
- Joined: Tue May 24, 2011 5:07 pm
- MMOC Member: Yes
-
- Series MM Registrar
- Posts: 10183
- Joined: Sun Jul 24, 2005 11:39 pm
- Location: Reading
- MMOC Member: No
Re: Ignition bits, original fittings. Advice needed.
DKYH4A side entry distributor cap, black copper core HT leads with brass eye ends secured with spark plug caps.
The coil lead is attached to the black coil with a brass split washer and "acorn" cap
I use a top entry distributor cap, HT leads secured by "acorn" caps and vertical spark plug caps
The coil lead is attached to the black coil with a brass split washer and "acorn" cap
I use a top entry distributor cap, HT leads secured by "acorn" caps and vertical spark plug caps
[sig]3580[/sig]
-
- Minor Friendly
- Posts: 52
- Joined: Tue May 24, 2011 5:07 pm
- MMOC Member: Yes
Re: Ignition bits, original fittings. Advice needed..
Thanks for the reply Mike.
From the info you have provided, I am happy with the dizzy cap and black HT leads which are in situ.
What I can't picture in my mind are the connections to the plugs and the coil. Please would it be possible to guide me to some photos that may be on the net with the correct fittings or some other images that will give me a clue to what it looks like.
Thanks again.
Pete.
From the info you have provided, I am happy with the dizzy cap and black HT leads which are in situ.
What I can't picture in my mind are the connections to the plugs and the coil. Please would it be possible to guide me to some photos that may be on the net with the correct fittings or some other images that will give me a clue to what it looks like.
Thanks again.
Pete.
-
- Series MM Registrar
- Posts: 10183
- Joined: Sun Jul 24, 2005 11:39 pm
- Location: Reading
- MMOC Member: No
Re: Ignition bits, original fittings. Advice needed.
I would recommend a copy of "Original Morris Minor" by Ray Newell, it has a good selection of photos of fixtures and fittings on Minors
[sig]3580[/sig]
-
- Minor Addict
- Posts: 978
- Joined: Thu Oct 04, 2012 5:01 pm
- Location: Farnborough, Hampshire
- MMOC Member: Yes
Re: Ignition bits, original fittings. Advice needed.
Hello Pete,
Only just seen this post.
If you can wait until I get home, tonight, I can post up pictures of my sidevalve engine, with original side-entry dizzy cap.
The only mods on this one are the "electronic ignition" module fitted inside the cap.
Or you can see some of the connections etc., in this topic
http://www.mmoc.org.uk/viewtopic.php?f= ... electronic
George.
Only just seen this post.
If you can wait until I get home, tonight, I can post up pictures of my sidevalve engine, with original side-entry dizzy cap.
The only mods on this one are the "electronic ignition" module fitted inside the cap.
Or you can see some of the connections etc., in this topic
http://www.mmoc.org.uk/viewtopic.php?f= ... electronic
George.
'50 Low-light with 918 Side-valve engine,
'51 High-light with Side-valve 918 engine,
'55 4-dr with 803 engine,
'56 Traveller with 1098 engine.
-
- Minor Friendly
- Posts: 52
- Joined: Tue May 24, 2011 5:07 pm
- MMOC Member: Yes
Re: Ignition bits, original fittings. Advice needed.
Hi
Thank you for your replies on this subject. I have obtained the plug connectors and almost ready to convert back to original spec. I have noticed from the 'Original Morris Minor' publication (thanks Mike for the tip), that there seems to be a 'sleeve' or is it black electrical tape attached to the plug end of the HT lead?
Hope you can see what I mean from the photos below.
Please could I have some advice on this and if it is a purchasable item, where I can get them.
Thank you.
Pete[frame]
[/frame][frame]
[/frame]
Thank you for your replies on this subject. I have obtained the plug connectors and almost ready to convert back to original spec. I have noticed from the 'Original Morris Minor' publication (thanks Mike for the tip), that there seems to be a 'sleeve' or is it black electrical tape attached to the plug end of the HT lead?
Hope you can see what I mean from the photos below.
Please could I have some advice on this and if it is a purchasable item, where I can get them.
Thank you.
Pete[frame]
-
- Minor Addict
- Posts: 550
- Joined: Wed Jul 28, 2010 9:39 am
- Location: Netherlands, Drenthe
- MMOC Member: No
Re: Ignition bits, original fittings. Advice needed.
the yellow cables with copper connections for the spark plugs, are they original?
Nice to have these for my car ;)
Nice to have these for my car ;)
MM '51 LHD sidevalve ![](mbimage.php?src=sig_12584)
-
- Minor Legend
- Posts: 3010
- Joined: Sun Sep 09, 2007 10:42 pm
- Location: Whiteabbey, Co Antrim
- MMOC Member: Yes
Re: Ignition bits, original fittings. Advice needed.
I would think that it is an insulating sleeve that covers were the connector is cramped onto the lead
Too many Minors so little time.....
-
- Minor Addict
- Posts: 550
- Joined: Wed Jul 28, 2010 9:39 am
- Location: Netherlands, Drenthe
- MMOC Member: No
Re: Ignition bits, original fittings. Advice needed.
and the copper nuts, where to find?
and the rings, they are not standard, they need a small hole, and a bigger hole, for the ignition cable, nice to have it ;)
with a standard crimping tool it is not a problem.
and the rings, they are not standard, they need a small hole, and a bigger hole, for the ignition cable, nice to have it ;)
with a standard crimping tool it is not a problem.
MM '51 LHD sidevalve ![](mbimage.php?src=sig_12584)