Can someone tell what parts are needed for mounting these parts?
I can order this one at ESM:
http://www.morrisminorspares.com/coolin ... ve-p829614
but the other hole need a part to close it, I think a drain or something like that..
Sometimes the pump is on Ebay, but never seen the other parts.
Parts needed for waterpump mounting on USHM3
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
-
- Minor Addict
- Posts: 550
- Joined: Wed Jul 28, 2010 9:39 am
- Location: Netherlands, Drenthe
- MMOC Member: No
Parts needed for waterpump mounting on USHM3
MM '51 LHD sidevalve
-
- Minor Legend
- Posts: 2646
- Joined: Thu May 11, 2006 10:34 am
- Location: Cardiff
- MMOC Member: Yes
Re: Parts needed for waterpump mounting on USHM3
I seem to remember that the 2 bolts for this part are 8mm Metric Fine thread, not British sizes, although corrosion makes the Metric ones loose and 5/16 is about 7.95mm. Drain hole is maybe BSP thread? Try the one from the Morris 1000 radiator or even close it with weld? The drain is only there for very cold days if you want to empty the engine overnight.
Cardiff, UK
-
- Minor Addict
- Posts: 550
- Joined: Wed Jul 28, 2010 9:39 am
- Location: Netherlands, Drenthe
- MMOC Member: No
Re: Parts needed for waterpump mounting on USHM3
I can re-use the original M8x1.0 bolts, but the drain is what I like to have as original as possible.
Not for cold weather, my garage has floor heating, and the car is only on the road when it is not freezing ;)
Not for cold weather, my garage has floor heating, and the car is only on the road when it is not freezing ;)
MM '51 LHD sidevalve
-
- Minor Legend
- Posts: 2646
- Joined: Thu May 11, 2006 10:34 am
- Location: Cardiff
- MMOC Member: Yes
Re: Parts needed for waterpump mounting on USHM3
http://www.bmcfarina.com/contents/en-uk ... iator.html ???
If you can give me 1/2 hour I shall find the correct part number for it.
Rob
If you can give me 1/2 hour I shall find the correct part number for it.
Rob
Cardiff, UK
-
- Minor Legend
- Posts: 2646
- Joined: Thu May 11, 2006 10:34 am
- Location: Cardiff
- MMOC Member: Yes
Re: Parts needed for waterpump mounting on USHM3
163129 is the Series MM drain part number. The image in the book shows it to have a single bent arm rather than the winged arm in the link above. It also shows a washer which suggests that it is a parallel thread, not a tapering one.
The MM Radiator drain part number is ARH515, so, it isn't the same part but looks similar.
Maybe like this...? http://britishclassicspareparts.com.au/ ... mini-riley
I hope this helps.
Rob
The MM Radiator drain part number is ARH515, so, it isn't the same part but looks similar.
Maybe like this...? http://britishclassicspareparts.com.au/ ... mini-riley
I hope this helps.
Rob
Cardiff, UK
Re: Parts needed for waterpump mounting on USHM3
I've a feeling the thread in the alloy water housing should be 1/8" BSP - I'd ask ESM to confirm that this is the case - if so then the following brass drain taps on the vintagecarparts website should fit, together with a suitable fibre washer - their part numbers are: 341 & 338.
1/8" x 28 TPI BSP.
https://www.vintagecarparts.co.uk/categ ... taps-drain
1/8" x 28 TPI BSP.
https://www.vintagecarparts.co.uk/categ ... taps-drain