Vacuum/Economy Gauge Piping
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
- Monty-4
- Minor Addict
- Posts: 699
- Joined: Sun Oct 26, 2014 7:17 pm
- Location: Gloucestershire
- MMOC Member: Yes
Vacuum/Economy Gauge Piping
I'm a sucker for old gadgets such as these and this one was both shiny and colourful, I had to buy it! So now I've got to connect it.
My engine is currently running twin HS2s on a old style manifold (AUE1020). The vacuum advance connection on the carb is the type that is really close behind the carb butterfly so doesn't give a reading at idle, but does once the throttle is opened just a little. As such I don't think the gauge would really work properly if I just add a t-piece in there somewhere. What does the forum's collective mind think would be the best way to rearrange or add to this for the gauge? Once aspect I've been wondering about is whether it would be best to pull the vacuum 'signal' from both carbs for the vacuum advance and the gauge.
So how about I;
1. Add a take-off on the manifold (no idea what the thread is though) or a single manifold spacer with a take-off and run straight to gauge (don't touch the vacuum advance connection).
2. Add two manifold spacers with take-offs to cover both carbs and join with a T-piece (don't touch the vacuum advance connection).
3. Switch the vacuum advance pipe to the manifold or a spacer (or two) and add a T-piece for the gauge closer to the dizzy.
My engine is currently running twin HS2s on a old style manifold (AUE1020). The vacuum advance connection on the carb is the type that is really close behind the carb butterfly so doesn't give a reading at idle, but does once the throttle is opened just a little. As such I don't think the gauge would really work properly if I just add a t-piece in there somewhere. What does the forum's collective mind think would be the best way to rearrange or add to this for the gauge? Once aspect I've been wondering about is whether it would be best to pull the vacuum 'signal' from both carbs for the vacuum advance and the gauge.
So how about I;
1. Add a take-off on the manifold (no idea what the thread is though) or a single manifold spacer with a take-off and run straight to gauge (don't touch the vacuum advance connection).
2. Add two manifold spacers with take-offs to cover both carbs and join with a T-piece (don't touch the vacuum advance connection).
3. Switch the vacuum advance pipe to the manifold or a spacer (or two) and add a T-piece for the gauge closer to the dizzy.
68' 4-door Saloon, another 'Monty'.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Just fit a vacuum take off into the manifold using one of the blanked holes.
The large plug thread should be 5/8" UNF.
If you have the smaller blanking plug(s) fitted post the dia on here and I will give you the thread.
BMC did make an 5/8" UNF adapter to enable the vacuum to run vacuum operated windscreen washers on the MGA.
If I can find the adapter I will post a picture.
The large plug thread should be 5/8" UNF.
If you have the smaller blanking plug(s) fitted post the dia on here and I will give you the thread.
BMC did make an 5/8" UNF adapter to enable the vacuum to run vacuum operated windscreen washers on the MGA.
If I can find the adapter I will post a picture.
- Monty-4
- Minor Addict
- Posts: 699
- Joined: Sun Oct 26, 2014 7:17 pm
- Location: Gloucestershire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
The blank that secures the vacuum flame trap looks like the best candidate, others are taken by the PCV valve and the throttle cable bracket. Looks like a coarse thread to me, UNC? BSF? BSP? 1/4 or 5/16... something.
68' 4-door Saloon, another 'Monty'.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Thanks for posting
What you have described and what you have shown in measurement (0.3125 Dec) leads me to believe that the thread is 5/16" x 18 TPI UNC.
The threads in a BMC manifold are normally either UNF or UNC.
Is that hole blind or does it go right through into the inlet manifold tract?
Phil
What you have described and what you have shown in measurement (0.3125 Dec) leads me to believe that the thread is 5/16" x 18 TPI UNC.
The threads in a BMC manifold are normally either UNF or UNC.
Is that hole blind or does it go right through into the inlet manifold tract?
Phil
- Monty-4
- Minor Addict
- Posts: 699
- Joined: Sun Oct 26, 2014 7:17 pm
- Location: Gloucestershire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Straight through into the tract.
68' 4-door Saloon, another 'Monty'.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Thank you for the detail.
If that is the case I would relocate the flame trap and use the drilling to fit an adapter.
If that is the case I would relocate the flame trap and use the drilling to fit an adapter.
-
- Minor Legend
- Posts: 1904
- Joined: Sun Jul 03, 2011 11:37 am
- Location: Near Belper
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
I can almost see why you want one
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
- Monty-4
- Minor Addict
- Posts: 699
- Joined: Sun Oct 26, 2014 7:17 pm
- Location: Gloucestershire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Any ideas where I could find a 5/16 UNC (to 1/4" or 1/8" pipe) hose tail? They all appear to be BSP!
68' 4-door Saloon, another 'Monty'.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
If you cannot find one make your own.
Centre drill a 5/16" UNC bolt and solder or braze a piece of brake pipe into the hole. A piece of old brake pipe with the nipple on the end would be ideal.
Before doing anything confirm that the existing hole is 5/16" UNC.
The normal vacuum take off union for the servo is also shown below. The thread is 5/8" x 18 TPI UNF.
The bottom photo is the vacuum take off fitted to a MGA inlet manifold to provide a vacuum source for the windscreen washers.
The thread is 5/8" x 16 TPI UNS.
Both of these vacuum take off unions would normally be fitted into the unused bosses of the twin carb manifold shown above
Phil
Centre drill a 5/16" UNC bolt and solder or braze a piece of brake pipe into the hole. A piece of old brake pipe with the nipple on the end would be ideal.
Before doing anything confirm that the existing hole is 5/16" UNC.
The normal vacuum take off union for the servo is also shown below. The thread is 5/8" x 18 TPI UNF.
The bottom photo is the vacuum take off fitted to a MGA inlet manifold to provide a vacuum source for the windscreen washers.
The thread is 5/8" x 16 TPI UNS.
Both of these vacuum take off unions would normally be fitted into the unused bosses of the twin carb manifold shown above
Phil
- Attachments
-
- Vacuum take off 2 MGA.JPG (1.41 MiB) Viewed 2690 times
-
- vacuum take off MGA.JPG (1.36 MiB) Viewed 2691 times
- Monty-4
- Minor Addict
- Posts: 699
- Joined: Sun Oct 26, 2014 7:17 pm
- Location: Gloucestershire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Thanks again for the help and advice - here is a wobbly video taken by my passenger today. I think I'm saving fuel already trying to get the gauge to show as high as possible!
https://youtu.be/KXcjanrie5U
https://youtu.be/KXcjanrie5U
68' 4-door Saloon, another 'Monty'.
-
- Minor Addict
- Posts: 667
- Joined: Sun Aug 27, 2017 6:05 pm
- Location: West Yorkshire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Hi Monty
Can I ask you to give us some details of how you made and fixed the new dash panel into place please.
I am just at the point of doing exactly the same thing myself.
Thanks
Phil
Can I ask you to give us some details of how you made and fixed the new dash panel into place please.
I am just at the point of doing exactly the same thing myself.
Thanks
Phil
- Monty-4
- Minor Addict
- Posts: 699
- Joined: Sun Oct 26, 2014 7:17 pm
- Location: Gloucestershire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Sure thing. Not an expert job but here were the steps:
1 - Made a paper template of the shape of the glove box arround opening, plus 3-4mm, with circles for planned gauges, and stuck it to cheap 1mm steel sheet.
2 - Cut steel to shape and used circle cutter for holes, filed burr off edges.
3 - Stuck veneer (smoked sapele) on with basic wood glue, cut holes with scalpel.
4 - Teak/reddish stain, followed by clear varnish.
5 - Bonded panel to back of glove box surround with Araldite, sealed a couple places where it lifted with Sugru (the back is not entirely flat, a more flexible metal such as aluminium would have been far easier).
6 - Gauges are held in by interference and the normal clamps.
Good luck.
1 - Made a paper template of the shape of the glove box arround opening, plus 3-4mm, with circles for planned gauges, and stuck it to cheap 1mm steel sheet.
2 - Cut steel to shape and used circle cutter for holes, filed burr off edges.
3 - Stuck veneer (smoked sapele) on with basic wood glue, cut holes with scalpel.
4 - Teak/reddish stain, followed by clear varnish.
5 - Bonded panel to back of glove box surround with Araldite, sealed a couple places where it lifted with Sugru (the back is not entirely flat, a more flexible metal such as aluminium would have been far easier).
6 - Gauges are held in by interference and the normal clamps.
Good luck.
68' 4-door Saloon, another 'Monty'.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Well done and thanks for the video.
A description and a photo of the fittings to the manifold would be appreciated.
Phil
A description and a photo of the fittings to the manifold would be appreciated.
Phil
- Monty-4
- Minor Addict
- Posts: 699
- Joined: Sun Oct 26, 2014 7:17 pm
- Location: Gloucestershire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
I'm embarrassed to say I 'cheated' - lacking a pillar drill and my normal drill being knackered I didn't think trying to bore out a bolt would be fun.
Instead I dug out a spare carb spacer and fit it with a tail for hose of approx 4mm ID (5/32"?), the same as the tail on the back of the gauge. After doing this I realised I didn't have a long enough length of hose to reach friom the manifold to the gauge panel (using offcuts of braided fuel hose from another job), so have two reducers and a length of 3mm (1/8") hose between them, nipped up with jubilee clips as it leaked vacuum without them. The slimmer hose and reducers will likely stay in place indefinitely as it helps it squeeze into the existing hole in the bulkhead that carries the wiring loom.
Instead I dug out a spare carb spacer and fit it with a tail for hose of approx 4mm ID (5/32"?), the same as the tail on the back of the gauge. After doing this I realised I didn't have a long enough length of hose to reach friom the manifold to the gauge panel (using offcuts of braided fuel hose from another job), so have two reducers and a length of 3mm (1/8") hose between them, nipped up with jubilee clips as it leaked vacuum without them. The slimmer hose and reducers will likely stay in place indefinitely as it helps it squeeze into the existing hole in the bulkhead that carries the wiring loom.
Last edited by Monty-4 on Thu Apr 05, 2018 10:05 pm, edited 1 time in total.
68' 4-door Saloon, another 'Monty'.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Monty-4
Thank you for the post above.
As you have twin carbs did you put the same or similar thickness spacer between the other carb and manifold so as to keep the carb linkage parallel with the manifold?
Also where does the pipe to the PCV valve come from?
Phil
Thank you for the post above.
As you have twin carbs did you put the same or similar thickness spacer between the other carb and manifold so as to keep the carb linkage parallel with the manifold?
Also where does the pipe to the PCV valve come from?
Phil
- Monty-4
- Minor Addict
- Posts: 699
- Joined: Sun Oct 26, 2014 7:17 pm
- Location: Gloucestershire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
I did indeed put a matching spacer on the other side so the carbs are equally spaced, getting them back on with the linkages not falling through the engine bay is always heaps of fun.
The pipe from the PCV valve routes under the airboxes to a tappet breather canister (from a Mini I think) stuffed with stainless steel dish scrubbers.
The pipe from the PCV valve routes under the airboxes to a tappet breather canister (from a Mini I think) stuffed with stainless steel dish scrubbers.
68' 4-door Saloon, another 'Monty'.
-
- Minor Legend
- Posts: 1667
- Joined: Thu May 12, 2016 6:33 am
- MMOC Member: No
Re: Vacuum/Economy Gauge Piping
... as it leaked vacuum without them ...
Can’t help but be pedantic on this! I have never ever experienced a vacuum leaking anywhere. First there would be nothing to leak and secondly it would (usually) be air that was leaking through any orifices into the lower pressure area.
Can’t help but be pedantic on this! I have never ever experienced a vacuum leaking anywhere. First there would be nothing to leak and secondly it would (usually) be air that was leaking through any orifices into the lower pressure area.
-
- Minor Maniac
- Posts: 10818
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
Monty-4
Thank you for the pictures and description.
An observation:-
The flame trap in the vacuum advance pipe should be vertical so as to stop any unburnt fuel getting into the distributer and being ignited when the points open. Being vertical also stops the diaphragm in the vacuum advance unit from being contaminated by petrol.
Phil
Thank you for the pictures and description.
An observation:-
The flame trap in the vacuum advance pipe should be vertical so as to stop any unburnt fuel getting into the distributer and being ignited when the points open. Being vertical also stops the diaphragm in the vacuum advance unit from being contaminated by petrol.
Phil
- Monty-4
- Minor Addict
- Posts: 699
- Joined: Sun Oct 26, 2014 7:17 pm
- Location: Gloucestershire
- MMOC Member: Yes
Re: Vacuum/Economy Gauge Piping
That makes sense regarding the flame trap, thanks for the tip Phil. I well get on that as I'm running an "electronic" dizzy currently but will be switching back to trusty old points when the original 25D comes back from having it's timing curve changed and a general refurbishment.
oliver90owner, I'll have to let m'lady know that I've met my match when it comes to pedantry, she'll be quite surprised to hear it!
oliver90owner, I'll have to let m'lady know that I've met my match when it comes to pedantry, she'll be quite surprised to hear it!
68' 4-door Saloon, another 'Monty'.