Fitting water temp sender - to PTFE or not?
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
Fitting water temp sender - to PTFE or not?
Hi all,
I hope to spend this weekend fitting my new TIM electric water temp gauge and sender unit to my 1098 engine. I bought the gauge and sender unit as an 'all in one' kit from MiniSpares. The sender unit comes with a couple of adapters - as there is no washer, should I be using PTFE tape or similar to get a watertight seal - or would the PTFE interfere with the electrical grounding?
Many thanks in advance for your advice.
Pete
I hope to spend this weekend fitting my new TIM electric water temp gauge and sender unit to my 1098 engine. I bought the gauge and sender unit as an 'all in one' kit from MiniSpares. The sender unit comes with a couple of adapters - as there is no washer, should I be using PTFE tape or similar to get a watertight seal - or would the PTFE interfere with the electrical grounding?
Many thanks in advance for your advice.
Pete
-
- Minor Fan
- Posts: 228
- Joined: Wed Oct 13, 2010 7:24 pm
- MMOC Member: No
Re: Fitting water temp sender - to PTFE or not?
Pete I can't quite remember (it's been a few years since I did it!) but does the adaptor have a tapered thread so it seals without a washer?
Re: Fitting water temp sender - to PTFE or not?
A good question - I have yet to open the bag and have a look!
-
- Minor Fan
- Posts: 365
- Joined: Wed Feb 13, 2002 12:00 am
- Location: Huntingdon
- MMOC Member: Yes
Re: Fitting water temp sender - to PTFE or not?
I would be inclined to use as small amount of ptfe tape, assume that when you tighten it up the sender will cut through it and make contact with the engine and then check that you have an electrical connection with a meter.
-
- Minor Maniac
- Posts: 10908
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Fitting water temp sender - to PTFE or not?
https://www.minispares.com/product/Clas ... o%20search
There is no requirement to use PTFE tape.
The transmitter and adapters (if required) should be self sealing.
Just make sure that the thread in the head is clean before fitting the transmitter/adapter(s).
https://www.minispares.com/product/Clas ... o%20search
There is no requirement to use PTFE tape.
The transmitter and adapters (if required) should be self sealing.
Just make sure that the thread in the head is clean before fitting the transmitter/adapter(s).
https://www.minispares.com/product/Clas ... o%20search
Re: Fitting water temp sender - to PTFE or not?
Many thanks all, @Philthehill, the top link is the item I bought - I appreciate your comments and will report back how it goes.
All the best,
Pete
All the best,
Pete
- geoberni
- Minor Legend
- Posts: 3652
- Joined: Fri Aug 04, 2017 11:19 am
- Location: North Leicestershire
- MMOC Member: Yes
Re: Fitting water temp sender - to PTFE or not?
Personally I'd use a little ptfe tape just at the top of the thread almost as a washer. Just because I could.
No need to overly worry about metal to metal contact for completing the circuit, the water will happily that![Happy :D](./images/smilies/icon_biggrin.gif)
No need to overly worry about metal to metal contact for completing the circuit, the water will happily that
![Happy :D](./images/smilies/icon_biggrin.gif)
Basil the 1955 series II
![Image](https://image.ibb.co/hrLO0J/DSCF8095_F.jpg)
![Image](https://image.ibb.co/hrLO0J/DSCF8095_F.jpg)
-
- Minor Maniac
- Posts: 10908
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Fitting water temp sender - to PTFE or not?
The electrical transmitter is sealed by the concave taper in the head and the convex taper at the inner end of the transmitter. The threads form no part of the sealing.
Re: Fitting water temp sender - to PTFE or not?
Incorrect, the circuit needs to be via the block directly, the water will form a very poor electrical connection, even with coolant in it.
- geoberni
- Minor Legend
- Posts: 3652
- Joined: Fri Aug 04, 2017 11:19 am
- Location: North Leicestershire
- MMOC Member: Yes
Re: Fitting water temp sender - to PTFE or not?
I bow to your experience. I've personally always found water a very good and often most inconvenient conductor.
Though I admit I've never relied on it for the temp sender.
![:wink:](./images/smilies/icon_wink.gif)
Basil the 1955 series II
![Image](https://image.ibb.co/hrLO0J/DSCF8095_F.jpg)
![Image](https://image.ibb.co/hrLO0J/DSCF8095_F.jpg)