Fitting water temp sender - to PTFE or not?

Discuss mechanical problems here.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
Post Reply
Pete Bags
Minor Fan
Posts: 119
Joined: Fri May 01, 2020 1:21 pm
MMOC Member: Yes

Fitting water temp sender - to PTFE or not?

Post by Pete Bags »

Hi all,

I hope to spend this weekend fitting my new TIM electric water temp gauge and sender unit to my 1098 engine. I bought the gauge and sender unit as an 'all in one' kit from MiniSpares. The sender unit comes with a couple of adapters - as there is no washer, should I be using PTFE tape or similar to get a watertight seal - or would the PTFE interfere with the electrical grounding?

Many thanks in advance for your advice.

Pete
Biggles1957
Minor Fan
Posts: 228
Joined: Wed Oct 13, 2010 7:24 pm
MMOC Member: No

Re: Fitting water temp sender - to PTFE or not?

Post by Biggles1957 »

Pete I can't quite remember (it's been a few years since I did it!) but does the adaptor have a tapered thread so it seals without a washer?
Pete Bags
Minor Fan
Posts: 119
Joined: Fri May 01, 2020 1:21 pm
MMOC Member: Yes

Re: Fitting water temp sender - to PTFE or not?

Post by Pete Bags »

A good question - I have yet to open the bag and have a look!
newagetraveller
Minor Fan
Posts: 365
Joined: Wed Feb 13, 2002 12:00 am
Location: Huntingdon
MMOC Member: Yes

Re: Fitting water temp sender - to PTFE or not?

Post by newagetraveller »

I would be inclined to use as small amount of ptfe tape, assume that when you tighten it up the sender will cut through it and make contact with the engine and then check that you have an electrical connection with a meter.
philthehill
Minor Maniac
Posts: 10767
Joined: Thu Jul 19, 2012 12:05 pm
Location: Hampshire
MMOC Member: Yes

Re: Fitting water temp sender - to PTFE or not?

Post by philthehill »

https://www.minispares.com/product/Clas ... o%20search

There is no requirement to use PTFE tape.
The transmitter and adapters (if required) should be self sealing.
Just make sure that the thread in the head is clean before fitting the transmitter/adapter(s).

https://www.minispares.com/product/Clas ... o%20search

Pete Bags
Minor Fan
Posts: 119
Joined: Fri May 01, 2020 1:21 pm
MMOC Member: Yes

Re: Fitting water temp sender - to PTFE or not?

Post by Pete Bags »

Many thanks all, @Philthehill, the top link is the item I bought - I appreciate your comments and will report back how it goes.

All the best,
Pete
User avatar
geoberni
Minor Legend
Posts: 3565
Joined: Fri Aug 04, 2017 11:19 am
Location: North Leicestershire
MMOC Member: Yes

Re: Fitting water temp sender - to PTFE or not?

Post by geoberni »

Personally I'd use a little ptfe tape just at the top of the thread almost as a washer. Just because I could.
No need to overly worry about metal to metal contact for completing the circuit, the water will happily that :D
Basil the 1955 series II

Image
philthehill
Minor Maniac
Posts: 10767
Joined: Thu Jul 19, 2012 12:05 pm
Location: Hampshire
MMOC Member: Yes

Re: Fitting water temp sender - to PTFE or not?

Post by philthehill »

The electrical transmitter is sealed by the concave taper in the head and the convex taper at the inner end of the transmitter. The threads form no part of the sealing.

Bowie69
Minor Fan
Posts: 196
Joined: Thu May 28, 2015 10:07 pm
MMOC Member: No

Re: Fitting water temp sender - to PTFE or not?

Post by Bowie69 »

geoberni wrote: Sat Sep 05, 2020 10:48 am Personally I'd use a little ptfe tape just at the top of the thread almost as a washer. Just because I could.
No need to overly worry about metal to metal contact for completing the circuit, the water will happily that :D
Incorrect, the circuit needs to be via the block directly, the water will form a very poor electrical connection, even with coolant in it.
User avatar
geoberni
Minor Legend
Posts: 3565
Joined: Fri Aug 04, 2017 11:19 am
Location: North Leicestershire
MMOC Member: Yes

Re: Fitting water temp sender - to PTFE or not?

Post by geoberni »

Bowie69 wrote: Sun Sep 06, 2020 11:07 am

Incorrect, the circuit needs to be via the block directly, the water will form a very poor electrical connection, even with coolant in it.
I bow to your experience. I've personally always found water a very good and often most inconvenient conductor.
Though I admit I've never relied on it for the temp sender. :wink:
Basil the 1955 series II

Image
Post Reply