I got a new number plate light & im wondering which wire goes where? Does the black or red or go the middle connection?
Thanks.
I’ve tried it both ways but it doesn’t work. So I’ll have to investigate further. The previous light worked before I changed it but the glass was broken & corroded so I got a new one
Number plate light
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
-
- Minor Friendly
- Posts: 76
- Joined: Sun May 08, 2022 6:09 pm
- MMOC Member: No
-
- Minor Legend
- Posts: 2781
- Joined: Tue Nov 11, 2014 9:41 am
- MMOC Member: No
Re: Number plate light
The red wire is the live 12volt supply so that needs to go to the (probably brass) contact which connects to the bottom of the bulb.
The black is the earth so that needs to connect with the side of the bulb - the body of the lamp.
Always a good idea to make a not or take a photograph before you dismantle anything
The black is the earth so that needs to connect with the side of the bulb - the body of the lamp.
Always a good idea to make a not or take a photograph before you dismantle anything
- svenedin
- Minor Legend
- Posts: 1960
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: Number plate light
When I changed mine I connected it up incorrectly and swiftly blew the fuse. Follow the earth wire back from the boot lid and check the earth is good.
Stephen
Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
- geoberni
- Minor Legend
- Posts: 3631
- Joined: Fri Aug 04, 2017 11:19 am
- Location: North Leicestershire
- MMOC Member: Yes
Re: Number plate light
Black is always the Earth Wire. Lamps always earth to the body.
Red is the Side Lights, which includes the number plate, so Red to central contact.
Make sure you have a supply, but also make sure the earth is good.
Use a meter if you have one, 12v on the red when switched on, and the Black should be near zero resistance, perhaps just an Ohm.
But don't forget to zero the meter before checking resistance. Exact method depending what sort of meter you're using.
Just follow the instructions that came with it.
Failing that, there's bound to be a Video for it on youtube...
Red is the Side Lights, which includes the number plate, so Red to central contact.
Make sure you have a supply, but also make sure the earth is good.
Use a meter if you have one, 12v on the red when switched on, and the Black should be near zero resistance, perhaps just an Ohm.
But don't forget to zero the meter before checking resistance. Exact method depending what sort of meter you're using.
Just follow the instructions that came with it.
Failing that, there's bound to be a Video for it on youtube...
Basil the 1955 series II
Re: Number plate light
If you did connect the wires the wrong way round at first then the fuse (if fitted) would have blown, meaning that the second attempt still won't work. Look below the voltage regulator for an inline fuse holder with red wires. Check and if necessary replace the fuse. NB 5 amp, not the 35 amp from the main fuse box.
As others have said, in the lamp unit then red to the base of the bulb and black to the frame/body.
As others have said, in the lamp unit then red to the base of the bulb and black to the frame/body.
-
- Minor Friendly
- Posts: 76
- Joined: Sun May 08, 2022 6:09 pm
- MMOC Member: No
Re: Number plate light
So it turns out it was a blown fuse. Inline fuse under the voltage regulator. Is it ok to rewire this for a newer blade style fuse holder?
- geoberni
- Minor Legend
- Posts: 3631
- Joined: Fri Aug 04, 2017 11:19 am
- Location: North Leicestershire
- MMOC Member: Yes
Re: Number plate light
That inline fuse is for far more than the Number Plate Light, it's all the side lights and the panel lights too.MoggyMatilda wrote: ↑Tue Feb 20, 2024 3:59 am So it turns out it was a blown fuse. Inline fuse under the voltage regulator. Is it ok to rewire this for a newer blade style fuse holder?
You probably ruptured it while fiddling with the number plate fitting.
It's you car, you can rewire it to a more modern one if you wish, but I don't understand why you think you need to. ....
Seems a pointless thing to do IMHO.
It did it's job and isolated the circuit when there was a fault.
Basil the 1955 series II
-
- Minor Friendly
- Posts: 76
- Joined: Sun May 08, 2022 6:09 pm
- MMOC Member: No
Re: Number plate light
My thinking was maybe the blade fuses are more readily available than the glass type? If I don’t have to rewire it I’ll leave it as is! Thanks!
- svenedin
- Minor Legend
- Posts: 1960
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: Number plate light
Glass type fuses are very readily available. Even Halfords sell them.MoggyMatilda wrote: ↑Tue Feb 20, 2024 10:18 am My thinking was maybe the blade fuses are more readily available than the glass type? If I don’t have to rewire it I’ll leave it as is! Thanks!
Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen