Rollover jig question
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
- Dryad
- Minor Addict
- Posts: 635
- Joined: Tue Jan 11, 2005 7:37 pm
- Location: South Norfolk
- MMOC Member: No
Rollover jig question
I have a rollover jig (two A-frames and bars which fix on to the bumper rods) built specifically for Minors. I need to do some welding underneath and have removed the engine, seats and bonnet, but left the gearbox, propshaft and rear axle on. Is it possible to roll over a Minor saloon with these items still on? The car is structurally sound, but I'm thinking that there might be too much weight below the centre of gravity to roll it. Anyone with experience of doing this?
-
- Minor Legend
- Posts: 2147
- Joined: Mon May 10, 2004 9:10 pm
- Location: Oxford, UK
- MMOC Member: Yes
Re: Rollover jig question
I would not leave just the gearbox in, as it is only secured at the rear. I would definitely remove both gearbox and propshaft.
The rear axle can be left in, BUT if you do make sure that you drain it completely of oil, otherwise when it is vertical, the oil will very likely leak through the seal and ruin the brake shoes! Probably easier to remove it?
My rollover jig mounts on the front and rear wheel fixings, so it needs to have the rear axle left in, which I did, and found out the oil leaking afterwards. At the time it was not very much of a problem, as the whole car was being restored, and the mechanical parts followed on after the bodywork, but if that is not the case, it's a real pain.
The rear axle can be left in, BUT if you do make sure that you drain it completely of oil, otherwise when it is vertical, the oil will very likely leak through the seal and ruin the brake shoes! Probably easier to remove it?
My rollover jig mounts on the front and rear wheel fixings, so it needs to have the rear axle left in, which I did, and found out the oil leaking afterwards. At the time it was not very much of a problem, as the whole car was being restored, and the mechanical parts followed on after the bodywork, but if that is not the case, it's a real pain.
Richard
- Dryad
- Minor Addict
- Posts: 635
- Joined: Tue Jan 11, 2005 7:37 pm
- Location: South Norfolk
- MMOC Member: No
Re: Rollover jig question
Good point! I'll remove the gearbox and propshaft and drain the oil from the axle then. Thanks.
-
- Minor Legend
- Posts: 1441
- Joined: Tue Jan 30, 2007 10:09 pm
- Location: Essex
- MMOC Member: No
Re: Rollover jig question
I think I would seal in the master cylinder brake fluid - to stop it spoiling your roof!
Alan
Alan
-
- Minor Addict
- Posts: 956
- Joined: Fri Aug 26, 2011 12:42 pm
- Location: West Yorkshire
- MMOC Member: Yes
Re: Rollover jig question
The centre of gravity on my home made scaffold pole & builders trestle rotisserie wasn't bad - but even with all the heavy components removed it could give you quite a wallop if you let it go at the wrong moment. I used a chain hoist slung from a roof beam to control its movement.
Mark
Mark
- Dryad
- Minor Addict
- Posts: 635
- Joined: Tue Jan 11, 2005 7:37 pm
- Location: South Norfolk
- MMOC Member: No
Re: Rollover jig question
Thanks Mark, this is what I'm worried about really. My thinking was that if I removed too much from the lower half of the car, would it suddenly flip over as I turned it. I suppose I should just be prepared.
Re: Rollover jig question
Can you post a picture of your jig i'm intrigued (and need one myself!)
- Dryad
- Minor Addict
- Posts: 635
- Joined: Tue Jan 11, 2005 7:37 pm
- Location: South Norfolk
- MMOC Member: No
Re: Rollover jig question
It's under some junk at the moment but it looks like this one, only without the facililty to adjust the centre of gravity. It was custom-built by someone who had restored several Minors:
https://www.youtube.com/watch?v=Spgy73QA3ss
https://www.youtube.com/watch?v=Spgy73QA3ss
-
- Minor Friendly
- Posts: 12
- Joined: Mon Nov 23, 2015 9:46 am
- MMOC Member: No
Re: Rollover jig question
I used to have a the smart or similar jig, I used to leave cars complete ( less fluids) and turn them no problem never had a problem with weight.
- Dryad
- Minor Addict
- Posts: 635
- Joined: Tue Jan 11, 2005 7:37 pm
- Location: South Norfolk
- MMOC Member: No
Re: Rollover jig question
I have removed the engine and I will be taking all four doors off (a considerable weight!) and the gearbox but will leave the rear axle on, I think.