There are no kits, you just buy the bits you want to change.
http://www.morrisminorspares.com/
What would that be?
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
-
- Minor Legend
- Posts: 2646
- Joined: Thu May 11, 2006 10:34 am
- Location: Cardiff
- MMOC Member: Yes
Re: What would that be?
Cardiff, UK
-
- Minor Friendly
- Posts: 94
- Joined: Fri Feb 25, 2011 2:34 pm
- Location: Mangalore , INDIA
- MMOC Member: No
Re: What would that be?
Hi,
Got the following items from the Spares man Mr Bryan.
Wiper motor, mount and brackets SH
Wiper drive cable, wheel boxes etc SH
Wiper arms black 2 no's
Rear brake cylinders Lockheed 2 No's
2 carbon brushes and springs for the distributor.
They shall be reaching here tomorrow.
Got the following items from the Spares man Mr Bryan.
Wiper motor, mount and brackets SH
Wiper drive cable, wheel boxes etc SH
Wiper arms black 2 no's
Rear brake cylinders Lockheed 2 No's
2 carbon brushes and springs for the distributor.
They shall be reaching here tomorrow.
[*]Pradeep Prabhu[*]
1951 Series MM - 2door - side valve head
1951 Series MM - 2door - side valve head
-
- Minor Friendly
- Posts: 94
- Joined: Fri Feb 25, 2011 2:34 pm
- Location: Mangalore , INDIA
- MMOC Member: No
Re: What would that be?
What is the nut thread size for the oil bath filter. Need to but a nut .
picture is as shown below.
picture is as shown below.
- Attachments
-
- IMG_4674.JPG (142.67 KiB) Viewed 2278 times
[*]Pradeep Prabhu[*]
1951 Series MM - 2door - side valve head
1951 Series MM - 2door - side valve head
-
- Minor Legend
- Posts: 2646
- Joined: Thu May 11, 2006 10:34 am
- Location: Cardiff
- MMOC Member: Yes
Re: What would that be?
That filter only went to 'Export' countries so we don't have them in the UK. Can you measure the thickness of the metal rod and see how many turns of thread there would be in one inch of rod?
Cardiff, UK
-
- Minor Addict
- Posts: 550
- Joined: Wed Jul 28, 2010 9:39 am
- Location: Netherlands, Drenthe
- MMOC Member: No
Re: What would that be?
I checked it on my filters, it looks like 5 mm, but the metric 5 tapped does not go in the nut for more than a few windings.
So it must be the BSF thread , possible 3/16 " ?
So it must be the BSF thread , possible 3/16 " ?
MM '51 LHD sidevalve
-
- Minor Maniac
- Posts: 10908
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: What would that be?
The part number for the air cleaner wing nut is AAA3936 / 184825 (MOSS).
A plain washer and a spring washer is also fitted and are installed under the wing nut - plain washer against the top of the filter.
I would suggest that the wing nut required is 1/4" UNF or at most 5/16" UNF.
A plain washer and a spring washer is also fitted and are installed under the wing nut - plain washer against the top of the filter.
I would suggest that the wing nut required is 1/4" UNF or at most 5/16" UNF.